Airtac TACE Guided Compact Cylinder TACE63X40S
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X40S is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 40mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke40 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X40S
Built as a double acting, non-rotating ISO 21287 compact cylinder, the TACE63X40S turns a 63 mm bore into 1558.6 N of push and 1458.1 N of pull at 0.5 MPa (2182.1 N push at 0.7 MPa). Twin guide rods ride on a yoke beside the 16 mm rod, so tooling cannot rotate and side loads are carried without an external guide - a real edge over a plain compact cylinder. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs, guards and gantries.
For real-world sizing, plan on about 935 N of usable push at 0.5 MPa (roughly 0.6 of the rated force); vertically that is about 158 kg theoretical, or about 79 kg with a 2:1 margin. The hard-anodized aluminium body carries a hard-chrome-plated S45C rod, a fixed TPU bumper absorbs end-of-stroke shock at each end, and the fitted -S magnet accepts CMSE / DMSE switches in the body slots. Supply 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, 1/8" port, female M10x1.5 rod thread.
Airtac TACE Guided Compact Cylinder TACE63X40S Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X40S |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 40 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X40S
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X40S Is Used
Press-fit arbor for EV connector housings
A 40 mm stroke covers approach plus load travel on a bench press-fit station; 1558.6 N at 0.5 MPa seats housings while the twin-guide yoke keeps the arbor square to the part.
Vertical pick of die inserts
The bore lifts about 79 kg with a 2:1 margin, enough to raise a steel die insert from a nest on a transfer line; the fitted -S magnet with a CMSE or DMSE switch confirms end of stroke.
Side clamp on extrusion conveyor fixtures
Clamps aluminium extrusion against a hard stop between cuts; the twin guide rods carry the side load of the clamp arm without an external guide, and the 1/8" port keeps plumbing compact.
Is the Airtac TACE Guided Compact Cylinder TACE63X40S the Right Cylinder?
With 1558.6 N of push at 0.5 MPa, this 63 mm bore sits mid-range: drop to 50 mm (981.7 N) for lighter clamping, or step up to 80 mm (2513.3 N) when the load grows. The piston drifts if air is lost, so fit a rod lock or pilot check valve where a load must stay put. Mounting covers FB flange, CA/CB clevis, CR and FTC; the -S magnet is already fitted on this model for CMSE / DMSE position sensing, and the female M10x1.5 rod thread accepts standard knuckle joints.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X40S FAQ
At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa those rise to 2182.1 N push and 2041.3 N pull. The theoretical maximum is 317.9 kgf at 1.0 MPa. Working pressure is 0.15-1.0 MPa (22-145 psi) and speed runs 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a hard-anodized aluminium barrel, S45C hard-chrome rod and a fixed TPU bumper at each end. Mounting options are FB flange, CA/CB clevis, CR and FTC. This -S model carries the optional magnet, so CMSE / DMSE reed or solid-state switches mount in the body slots; the 1/8" port and female M10x1.5 rod thread are standard for this bore.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X40S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.