Airtac TACE Guided Compact Cylinder TACE63X75
The AirTAC Airtac TACE Guided Compact Cylinder TACE63X75 is a genuine double acting, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACE Guided Compact Cylinder TACE63X75
The TACE63X75 is a double acting, non-rotating compact cylinder built to ISO 21287: a 63 mm bore with a 75 mm stroke in a hard-anodized aluminium body that saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods on a yoke stop the tooling rotating and carry side load, so a clamping plate or gripper stays square without any external guide. At 0.5 MPa it pushes 1558.6 N and pulls 1458.1 N; at 0.7 MPa push rises to 2182.1 N.
Plan on roughly 935 N of usable push at 0.5 MPa (about 0.6 of the rated force), which corresponds to lifting about 79 kg vertically with a 2:1 margin. The 16 mm S45C rod is hard-chrome plated with an M10x1.5 female thread, air ports are 1/8", and a fixed TPU bumper at each end absorbs end-of-stroke shock. Speed runs 30-500 mm/s across 0.15-1.0 MPa (22-145 psi). Without the optional -S magnet no position sensing is possible, so add -S if CMSE / DMSE switches are planned.
Airtac TACE Guided Compact Cylinder TACE63X75 Technical Specifications
| Model | Airtac TACE Guided Compact Cylinder TACE63X75 |
|---|---|
| Series | TACE compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 75 mm |
| Acting type | Double acting, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 1559 N | 1458 N |
| 0.7 MPa | 2182 N | 2041 N |
| Max (@1.0 MPa) | 318 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin. Twin guide rods stop the tooling rotating.
Model Code: Airtac TACE Guided Compact Cylinder TACE63X75
| TACE | ISO 21287 compact cylinder (non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACE Guided Compact Cylinder TACE63X75 Is Used
Bearing press station
Pressing sealed bearings into pump housings on a short-stroke press bench: the 75 mm stroke covers part placement plus press travel, and the twin-guide yoke keeps the mandrel square to the bore.
Machining fixture clamping
Clamping die-cast gearbox covers on a CNC milling fixture: 1558.6 N of push at 0.5 MPa holds the part through the cut, and the non-rotating guide rods keep the clamp pad flat against the casting.
Casting lift in a robot cell
Lifting about 79 kg aluminium castings between pallet and fixture in a machine-tending cell: the compact 63 mm body fits under a low gantry where a full-length profile cylinder would not.
Is the Airtac TACE Guided Compact Cylinder TACE63X75 the Right Cylinder?
In this force class the 63 mm bore sits between the 50 mm (981.7 N push at 0.5 MPa) and the 80 mm (2513.3 N push at 0.5 MPa): if your press or clamp needs under 900 N of real work the 50 mm saves air and space, while working forces above about 1400 N call for the 80 mm. The piston drifts when air is lost, so for a held load fit a rod lock or pilot check valve instead of relying on the cylinder. Mount with FB flange, CA/CB clevis, CR or FTC, and order the -S code if CMSE / DMSE switch sensing may be needed later.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACE Guided Compact Cylinder TACE63X75 FAQ
At 0.5 MPa it pushes with 1558.6 N and pulls with 1458.1 N. At 0.7 MPa push is 2182.1 N and pull is 2041.3 N. The theoretical maximum at 1.0 MPa is 317.9 kgf. For real work, plan on about 935 N of push at 0.5 MPa, which is roughly 79 kg of vertical lift with a 2:1 margin.
The ISO 21287 short body cuts mounting length by about 50% versus an ISO 15552 profile cylinder, so it fits tight jigs, guards and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock. Mounting choices are FB flange, CA/CB clevis, CR and FTC. Position sensing requires the optional -S magnet code; only with -S ordered can CMSE / DMSE switches be mounted. The port is 1/8" PT and the rod end is an M10x1.5 female thread.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACE Guided Compact Cylinder TACE63X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.