Airtac TACED Guided Compact Cylinder TACED25X30S
The AirTAC Airtac TACED Guided Compact Cylinder TACED25X30S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 30mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke30 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED25X30S
Double acting and double rod, the TACED25X30S pushes with 206.2 N and pulls with the same 206.2 N at 0.5 MPa, because a rod exits both covers and every stroke works on the rod-side area. Bore is 25 mm, stroke is 30 mm, and twin guide rods on a yoke stop the tooling rotating, so a gripper or plate stays square without an external guide. The optional -S magnet is fitted on this model, so CMSE / DMRE switches can be mounted - order CMSE / DMSE reed or solid-state switches to read position.
The hard-anodized aluminium body with an S45C hard-chrome rod runs at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s, with a fixed TPU bumper at each end. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into tight jigs and gantries. For planning: about 124 N (roughly 0.6 of the rated force) is a realistic working figure, which lifts about 10.5 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED25X30S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED25X30S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 30 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED25X30S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×30 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED25X30S Is Used
Fixture clamping in CNC jigs
The twin guide yoke holds a clamp plate square over the 30 mm stroke, and 206.2 N per side secures small aluminium parts during machining.
Pick-and-place of electronics trays
Equal 206.2 N force in both directions gives consistent grip and release, and the fitted -S magnet feeds CMSE / DMSE switch signals to the PLC.
Lab press and sample positioning
About 124 N of practical working force lifts roughly 10.5 kg vertically, and the short body fits under bench hoods where longer cylinders will not.
Is the Airtac TACED Guided Compact Cylinder TACED25X30S the Right Cylinder?
At 206.2 N per side, the 25 mm bore sits between the 20 mm bore (117.8 N) and the 32 mm bore (345.6 N) at 0.5 MPa - step down for lighter pick-and-place, up if you need more grip. The 30 mm stroke is within the standard range for this bore, so no made-to-order build is needed. Remember the piston drifts when air is lost; add a rod lock or pilot check valve if a load must stay put. FB flange mounting and the fitted -S magnet for CMSE / DMSE switches are both available.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED25X30S FAQ
Because it is a double-rod cylinder, force is equal in both directions: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa on the rod-side area, with a maximum of 42.0 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the port is M5x0.8.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and the S45C hard-chrome rod runs in a hard-anodized aluminium bore with a fixed TPU bumper at each end. The -S magnet is fitted on the TACED25X30S, so CMSE / DMSE reed or solid-state switches can be clamped into the body slots for end-of-stroke sensing.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED25X30S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.