Airtac TACED Guided Compact Cylinder TACED25X35S
The AirTAC Airtac TACED Guided Compact Cylinder TACED25X35S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 35mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke35 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED25X35S
The TACED25X35S is a double acting, double-rod compact cylinder built to the ISO 21287 short-body format, with a 25 mm bore and a 35 mm stroke. Because a rod exits both covers, the output force is equal in each direction: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, rising to a maximum of 42.0 kgf at 1.0 MPa. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. The S in the model code means the optional -S magnet is fitted, so CMSE / DMSE reed or solid-state switches can be mounted directly on the body slots.
The hard-anodized aluminium body with a roller-burnished bore carries an S45C hard-chrome-plated rod, and a fixed TPU bumper at each end absorbs end-of-stroke energy. Running on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), it cycles at 30-500 mm/s across -20 to +70 C. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs and guarding. For planning: at 0.5 MPa the 206.2 N rating works out to roughly 21 kg of vertical lift, so size real part weights at about 10 kg to keep a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED25X35S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED25X35S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED25X35S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED25X35S Is Used
Fixture clamping in machining cells
The equal 206.2 N force in both directions lets one TACED25X35S clamp and release a machined housing in a drill jig, with the twin guide rods keeping the clamp pad square to the datum.
Pusher on a packaging conveyor
A 35 mm stroke is enough to kick cartons sideways off a conveyor lane; the short ISO 21287 body fits under low guard rails where a full-length profile cylinder cannot.
Small-part gripper on an assembly robot
Mounted as a gripper actuator for connector housings, the non-rotating yoke holds jaw alignment, and the fitted -S magnet feeds CMSE switch signals back to the PLC for part-present checks.
Is the Airtac TACED Guided Compact Cylinder TACED25X35S the Right Cylinder?
At 206.2 N per direction at 0.5 MPa, the 25 mm bore sits between the 20 mm bore (117.8 N) and the 32 mm bore (345.6 N), so step down for lighter pick-and-place loads or up if your tooling needs more grip. The female M6x1.0 rod thread on both ends accepts standard rod accessories; there is no rod-thread option on the yoke itself. FB flange mounting is available, and the fitted -S magnet lets CMSE / DMSE switches report end positions. Note that the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must stay held.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED25X35S FAQ
The double-rod design gives equal force both ways because both sides work on the rod-side area: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, with a maximum of 42.0 kgf at 1.0 MPa. The 25 mm bore drives a 10 mm rod through a 35 mm stroke at 30-500 mm/s, on air at 0.15-1.0 MPa (22-145 psi).
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, S45C hard-chrome rod and fixed TPU bumpers at both ends, saving about 50% of the mounting length of an ISO 15552 profile cylinder. The S code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped into the body slots for end-of-stroke detection.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED25X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.