Airtac TACED Guided Compact Cylinder TACED25X50
The AirTAC Airtac TACED Guided Compact Cylinder TACED25X50 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 50mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke50 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED25X50
A double acting, double-rod ISO 21287 compact cylinder, the TACED25X50 pushes a 25 mm bore through a 50 mm stroke with a rod leaving both covers. Because both chambers see the rod-side area, output is 206.2 N in either direction at 0.5 MPa and 288.6 N at 0.7 MPa - no push/pull mismatch to design around. Twin guide rods on the yoke stop tooling rotation and carry side load, so a gripper or plate stays square without an external guide.
The hard-anodized aluminium body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, letting it slot into tight jigs and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock, the S45C hard-chrome rod resists wear, and the female M6x1.0 rod thread plus PT ports keep plumbing simple. In practice, plan on roughly 124 N of usable work at 0.5 MPa, and expect it to lift about 10 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED25X50 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED25X50 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED25X50
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED25X50 Is Used
Fixture clamping on CNC pallets
The 206.2 N clamping force acts identically on either rod end, so a machining fixture can be clamped or released from whichever side of the pallet is accessible.
Reject pusher on packaging lines
Twin guide rods keep the pusher plate square at 30-500 mm/s, kicking off-spec cartons off a conveyor without twisting or jamming.
Gripper actuation on small assembly cells
The non-rotating yoke holds jaw alignment for electronics sub-assembly work, with the 50 mm stroke opening wide enough for varied part sizes.
Is the Airtac TACED Guided Compact Cylinder TACED25X50 the Right Cylinder?
At 206.2 N per side at 0.5 MPa, this 25 mm bore sits between the 20 mm (117.8 N) and 32 mm (345.6 N) TACED sizes - step down for lighter pick-and-place heads, up for heavier clamping. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must be held. The 50 mm stroke is within the 150 mm standard range for this bore, and the optional -S magnet code enables CMSE / DMSE switches; without -S no magnet is fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED25X50 FAQ
Yes - the double-rod design exposes the rod-side area on both chambers, so output is equal both ways: 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa. At the full 1.0 MPa rating the cylinder reaches about 42.0 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, and the M5x0.8 port suits the 25 mm bore.
The ISO 21287 short-body build saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow guards and gantries. Each end carries a fixed TPU bumper that absorbs end-of-stroke energy; it is not adjustable and does not hold a load if air is lost. FB flange mounting is available, and ordering the optional -S magnet code lets CMSE / DMSE switches report position.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED25X50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.