Airtac TACED Guided Compact Cylinder TACED25X75
The AirTAC Airtac TACED Guided Compact Cylinder TACED25X75 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø25mm bore and 75mm stroke, M5×0.8 air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ25 mm
- Stroke75 mm
- Port sizeM5×0.8
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM6×1.0
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED25X75
A double acting compact cylinder built to ISO 21287, the TACED25X75 pushes a 25 mm bore through a 75 mm stroke with a rod leaving both covers. Because each side works on the rod-side area, output is a matched 206.2 N at 0.5 MPa (288.6 N at 0.7 MPa) in either direction. Twin guide rods on a yoke stop the tooling turning and take side load, so a gripper or press plate stays square without extra guiding. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs and guarding where a full-length body will not fit.
For sizing, plan on roughly 124 N of usable work at 0.5 MPa, which lifts about 10 kg vertically with a 2:1 margin. The hard-anodized aluminium body carries a hard-chrome plated S45C rod, a fixed TPU bumper absorbs the stroke ends, and the female M6x1.0 rod thread is ready for your tooling. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, and the optional -S magnet enables CMSE / DMSE switches; without -S there is no magnet fitted.
Airtac TACED Guided Compact Cylinder TACED25X75 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED25X75 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø25 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø25mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 206 N |
| 0.7 MPa | 289 N |
| Max (@1.0 MPa) | 42 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED25X75
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 25 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED25X75 Is Used
Bidirectional gripper actuation
Equal 206.2 N on open and close strokes suits a plastics-mould side gripper handling 10 kg parts, with the twin guide yoke keeping the fingers aligned.
Compact press station
A 75 mm stroke light staking or marking head on an electronics assembly bench, where the short ISO 21287 body fits inside the machine guard frame.
Push-pull tray transfer
Reciprocating a small packaging tray between lanes at 30-500 mm/s, using the same force in both travel directions and M5x0.8 ports on a compact manifold.
Is the Airtac TACED Guided Compact Cylinder TACED25X75 the Right Cylinder?
At 206.2 N both ways, the 25 mm bore sits between the 20 mm (117.8 N) and 32 mm (345.6 N) classes at 0.5 MPa - step down for lighter pick-and-place, up if your jig needs more clamping. The 75 mm stroke is within the 150 mm standard range for this bore, so it ships as a catalogue item. Remember the piston drifts when air is lost, so add a rod lock or pilot check valve if the load must stay put. Choose FB flange, CA, CB, CR or FTC mounts, and order the -S code if CMSE / DMSE position switches are planned.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED25X75 FAQ
Yes - the double-rod design means a rod exits both covers, so both strokes work on the rod-side area. Output is 206.2 N at 0.5 MPa and 288.6 N at 0.7 MPa, equal in both directions, with a maximum of 42.0 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body, S45C hard-chrome rod, threaded covers and a fixed TPU bumper at each stroke end - about 50% shorter in mounting length than an ISO 15552 profile cylinder. Sensing needs the optional -S magnet code; with it, CMSE / DMSE switches mount in the body slots. Without -S there is no magnet, so no switch will read.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED25X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.