Airtac TACED Guided Compact Cylinder TACED32X100S
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X100S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 100mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke100 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X100S
Double acting and double rod, the TACED32X100S pushes a 32 mm bore through a 100 mm stroke with a rod leaving both covers, so the force is identical in each direction: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or plate square without an external guide. The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be mounted anywhere along the body slots.
The hard-anodized aluminium body is an ISO 21287 compact build, roughly 50% shorter in mounting length than an ISO 15552 profile cylinder, which helps it slot into tight jigs and guarding. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the S45C hard-chrome plated rod resists wear. For planning: about 207 N of the 345.6 N rating is a realistic working force at 0.5 MPa, which corresponds to lifting roughly 17 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED32X100S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X100S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 100 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X100S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X100S Is Used
Symmetric jig clamping
Clamps a machined aluminium bracket in a drilling fixture from either side with matched 345.6 N force, so the part seats square without a clamp cylinder on the opposite face.
Push-pull tray transfer
On a packaging line, the through-rod advances and retracts a sliding tray with equal 483.8 N at 0.7 MPa, while the twin guide rods keep the pusher plate from twisting.
Gated assembly station
With the fitted -S magnet and DMSE switches, the 100 mm stroke confirms full advance and retract of a small pallet gate inside a compact cell where a longer body would not fit.
Is the Airtac TACED Guided Compact Cylinder TACED32X100S the Right Cylinder?
At 345.6 N per direction, this 32 mm bore sits between the 25 mm bore (206.2 N at 0.5 MPa) and the 40 mm bore (571.8 N at 0.5 MPa); step down for lighter clamping or up for heavier presses. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must be held. FB flange mounting suits plate-fixed installations, and the fitted -S magnet pairs with CMSE / DMSE switches for end-of-stroke or mid-stroke sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X100S FAQ
Yes. Because a rod exits both covers, both sides work on the rod-side area, so output is equal each way: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) and speed is 30-500 mm/s.
The ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke impact. The bumper only decelerates the piston; it never holds or brakes a load, and the piston will drift if air is lost. FB flange mounting is available, and the fitted -S magnet allows CMSE / DMSE switch mounting.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X100S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.