Airtac TACED Guided Compact Cylinder TACED32X15S
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X15S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 15mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke15 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X15S
Double acting and double rod, the AirTAC TACED32X15S pushes a rod out of BOTH covers, so its 32 mm bore delivers the same 345.6 N at 0.5 MPa in each direction - there is no weaker pull side. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight fixtures a full-length cylinder cannot.
The -S code on this model means the magnet is fitted, so CMSE / DMSE reed or solid-state switches can be clamped straight onto the body for end-of-stroke signals. A fixed TPU bumper at each end absorbs the stop, the hard-anodized aluminium body runs on a hard-chrome plated S45C rod, and the 15 mm stroke suits short clamp-and-release moves at 30-500 mm/s. As a working figure, plan on roughly 207 N of real work at 0.5 MPa - about 21 kg held vertically with margin.
Airtac TACED Guided Compact Cylinder TACED32X15S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X15S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 15 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X15S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X15S Is Used
Fixture clamping on CNC pallets
The 15 mm stroke clamps a machined blank against a stop in a tight pallet pocket, with equal 345.6 N release force so the part never sticks on retract.
Pick-and-place gripper jaws
Twin guide rods keep parallel jaws from twisting as they close on a 20 kg housing, and the fitted magnet feeds a CMSE switch signal to the PLC at each end.
Electronics assembly press station
A short press-in of a connector or bearing needs only 15 mm of travel; the compact body fits under a low gantry where a profile cylinder would not.
Is the Airtac TACED Guided Compact Cylinder TACED32X15S the Right Cylinder?
At 345.6 N per direction (483.8 N at 0.7 MPa, equal both ways), the 32 mm bore sits between the 25 mm bore at 206.2 N and the 40 mm bore at 571.8 N at 0.5 MPa - step down for light clamping, up for heavier pressing. The 15 mm stroke is a standard build, no made-to-order length needed. This model already carries the optional -S magnet for CMSE / DMSE switches, and the female M8x1.25 rod thread plus FB flange option covers most fixture mounts. Note it does not hold position if air is lost - add a rod lock or pilot check valve for a held load.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X15S FAQ
Yes - the double-rod design puts a rod through both covers, so both sides work on the rod-side area. At 0.5 MPa you get 345.6 N each way, at 0.7 MPa 483.8 N each way, and the maximum at 1.0 MPa is 70.5 kgf. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into cramped jigs and guards. A fixed TPU bumper at each end absorbs the end-of-stroke impact; it is not adjustable and it never locks the load. This -S model carries the magnet, so CMSE / DMSE switches mount on the body for position feedback.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X15S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.