Airtac TACED Guided Compact Cylinder TACED32X35S
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X35S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke35 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X35S
Double acting with a rod leaving both covers, the TACED32X35S pushes and pulls with identical force: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa in each direction, because both sides work on the rod-side area. Twin guide rods on the yoke stop the tooling rotating and take side load, so a gripper or press plate stays square without an external guide. The 35 mm stroke is a standard length for this 32 mm bore, and the fixed TPU bumper at each end absorbs end-of-stroke shock.
The body is a hard-anodized aluminium ISO 21287 compact build, roughly 50% shorter in mounting length than an ISO 15552 profile cylinder, which is why it drops into tight jigs and guarded cells where a full-length body will not fit. The S in the model code means the optional -S magnet is fitted, so CMSE or DMSE reed and solid-state switches can be clipped onto the body slot for end-position sensing. As a planning figure, treat about 207 N (roughly 17 kg vertical) as the usable working load at 0.5 MPa rather than the full rating.
Airtac TACED Guided Compact Cylinder TACED32X35S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X35S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X35S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X35S Is Used
Symmetric clamp fixtures
The equal 345.6 N push and pull clamps and releases a machined housing with the same force, so fixture engineers only size one number instead of two.
Pick-and-place gripper yoke
Twin guide rods keep the gripper jaws from rotating while the through-rod retracts with equal force, ideal for loading plastic connectors into a test nest.
Compact press station
With about 207 N of practical working force at 0.5 MPa and a 35 mm stroke, it suits light staking or marking on PCB brackets inside a guarded compact cell.
Is the Airtac TACED Guided Compact Cylinder TACED32X35S the Right Cylinder?
At 345.6 N per direction, this bore sits between the 25 mm size (206.2 N at 0.5 MPa) and the 40 mm size (571.8 N at 0.5 MPa); pick 25 mm for lighter clamping, 40 mm when you need over 570 N both ways. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, ports are 1/8" PT. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must be held. The fitted -S magnet pairs with CMSE / DMSE switches, and FB flange or CA/CB/CR/FTC mounts can be specified on the order code.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X35S FAQ
Yes. Because a rod exits both covers, both strokes act on the rod-side area, so force is equal both ways: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, with a maximum of 70.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, and the 1/8" PT port serves either end.
The hard-anodized aluminium ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, freeing space in tight gantries. The S in TACED32X35S means the optional -S magnet is fitted, so CMSE / DMSE switches mount in the body slot for position feedback. A fixed TPU bumper at each end softens stroke ends, and the female M8x1.25 rod thread on the yoke takes standard tooling.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.