Airtac TACED Guided Compact Cylinder TACED32X45S
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X45S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 45mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke45 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X45S
Double acting with a rod leaving both covers, the TACED32X45S delivers an equal 345.6 N in each direction at 0.5 MPa (483.8 N at 0.7 MPa) because both chambers work on the rod-side area. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. The 45 mm stroke sits well inside the 200 mm standard range for the 32 mm bore, and the optional -S magnet this model carries lets CMSE / DMRE-free CMSE / DMSE reed or solid-state switches report position directly on the body.
Built to ISO 21287, the hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs and guarding where a full-length body will not fit. The S45C hard-chrome rod and grease-storing two-way piston seal keep friction low over millions of cycles, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Plan on roughly 207 N of real work at 0.5 MPa, which is about 21 kg of horizontal push; vertically, halve the 35 kg lift equivalent and you can safely raise parts around 17 kg.
Airtac TACED Guided Compact Cylinder TACED32X45S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X45S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 45 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X45S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×45 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X45S Is Used
Pick-and-place on SMT feeders
The non-rotating twin guide yoke keeps a vacuum plate square over 45 mm of travel, and the fitted magnet feeds CMSE switch signals to the PLC for part-present checks.
Small press-fit of bushings
345.6 N at 0.5 MPa is enough to seat light bushings in aluminium housings; the equal both-way force retracts the mandrel with the same authority.
Bidirectional divert on packaging lines
A rod exits each cover, so one cylinder can push cartons left or right from a mid-line mount without reversing the body, at speeds up to 500 mm/s.
Is the Airtac TACED Guided Compact Cylinder TACED32X45S the Right Cylinder?
At 32 mm bore this unit gives 345.6 N both ways at 0.5 MPa - a step up from the 25 mm bore (206.2 N) if your fixture needs more clamp, and a step down from the 40 mm bore (571.8 N) if you are over-sizing. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, ports 1/8". Remember the piston drifts if air is lost, so add a rod lock or pilot check valve for a held load. FB flange mounting is available, and the fitted -S magnet means CMSE / DMSE switches can be added at any time.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X45S FAQ
Yes - it is a double-rod cylinder, so a rod exits both covers and both strokes act on the rod-side area. Output is 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, equal in each direction, with a maximum of 70.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, port 1/8", rod thread M8x1.25 female.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow gantries and guarded stations. The S means the optional magnet is fitted on this model, so CMSE / DMSE reed or solid-state switches can be clamped anywhere along the body slots. End-of-stroke shock is absorbed by a fixed TPU bumper at each cover, and FB flange mounting is available.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X45S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.