Airtac TACED Guided Compact Cylinder TACED32X50
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X50 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 50mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke50 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X50
A double acting, double-rod ISO 21287 compact cylinder, the TACED32X50 pushes a rod out of both covers so the 32 mm bore delivers 345.6 N at 0.5 MPa in each direction - rod-side area on both faces, no push-versus-pull gap. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide rail.
The short hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it drops into tight jigs, guarding and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the S45C hard-chrome rod resists wear. For sizing: plan on roughly 207 N (about 21 kg) of real work at 0.5 MPa, and the rod-side force equates to lifting about 17 kg vertically with a 2:1 margin. Runs on 0.15-1.0 MPa (22-145 psi) at 30-500 mm/s.
Airtac TACED Guided Compact Cylinder TACED32X50 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X50 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X50
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X50 Is Used
Symmetric jig clamping
Equal 345.6 N force from both rod ends lets one cylinder clamp from either face of a machining fixture, with the twin guide yoke keeping the clamp plate square.
Bidirectional pusher on packaging lines
A 50 mm stroke and identical push in both directions suits diverting cartons between conveyor lanes without a direction-dependent force change.
Compact gripper actuation
The non-rotating twin guide rods hold a two-jaw gripper aligned on small assembly cells, and the short body fits where a full-length profile cylinder will not.
Is the Airtac TACED Guided Compact Cylinder TACED32X50 the Right Cylinder?
At 345.6 N per side at 0.5 MPa, bore 32 suits clamping and transfer tasks in the 20-30 kg class. Step down to TACED25 (206.2 N) for lighter pick-and-place, or up to TACED40 (571.8 N) when the part weight grows. Note it does not hold position if air is lost - add a rod lock or pilot check valve for a held load. Mount with the FB flange where a fixed base is needed, and order the -S code if you want the optional magnet for CMSE / DMSE switches; without -S there is no magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X50 FAQ
Because a rod exits both covers, force is equal in both directions: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa, rising to a maximum of 70.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, speed 30-500 mm/s, air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end and FB flange mounting available. Sensing requires the optional -S magnet code: with -S ordered, CMSE / DMSE switches track position along the body slots; the standard TACED32X50 has no magnet fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.