Airtac TACED Guided Compact Cylinder TACED32X60
The AirTAC Airtac TACED Guided Compact Cylinder TACED32X60 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø32mm bore and 60mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ32 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED32X60
Double acting and double rod, the TACED32X60 pushes and pulls with identical force because a rod exits both covers and both sides work on the rod-side area. At 0.5 MPa it delivers 345.6 N in each direction, rising to 483.8 N at 0.7 MPa. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or plate stays square without an external guide. The 32 mm bore runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi) with a speed range of 30-500 mm/s.
This ISO 21287 compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarded gantries. The hard-anodized aluminium body carries a hard-chrome plated S45C rod, and a fixed TPU bumper at each end absorbs end-of-stroke energy. For sizing, plan on roughly 207 N of usable work at 0.5 MPa, which corresponds to lifting about 17 kg vertically with a 2:1 margin. No magnet is fitted; order the optional -S code if you need CMSE or DMSE switch sensing.
Airtac TACED Guided Compact Cylinder TACED32X60 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED32X60 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø32 mm |
| Stroke | 60 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø32mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 346 N |
| 0.7 MPa | 484 N |
| Max (@1.0 MPa) | 70 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED32X60
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 32 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED32X60 Is Used
Fixture clamping in tight machining cells
The compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, letting the 345.6 N clamp sit inside a crowded jig where a full-length cylinder will not fit.
Pick-and-place gripper actuation
Twin guide rods keep the gripper jaws from rotating and carry side load, while equal 345.6 N force in both directions gives identical grip and release on electronics housings.
Pusher on packaging lines
With about 207 N of usable work at 0.5 MPa and 30-500 mm/s speed, the 60 mm stroke pushes cartons square to the lane at high cycle rates without an external guide.
Is the Airtac TACED Guided Compact Cylinder TACED32X60 the Right Cylinder?
At 345.6 N per side at 0.5 MPa, the 32 mm bore sits between the 25 mm bore (206.2 N) and the 40 mm bore (571.8 N), so step up only if your fixture genuinely needs the extra thrust. The 60 mm stroke is within the standard range for this bore, so no made-to-order length is required. Remember the piston drifts when air is lost - for a held load add a rod lock or pilot check valve. FB flange mounting is available, and the female M8x1.25 rod thread on the yoke has no male-thread option. If you need position feedback, specify the -S suffix so CMSE or DMSE switches can be fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED32X60 FAQ
Yes. Because a rod exits both covers, both strokes work on the rod-side area, so output is equal both ways: 345.6 N at 0.5 MPa and 483.8 N at 0.7 MPa. The maximum force at 1.0 MPa is 70.5 kgf. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/8" port depends only on the 32 mm bore.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so the 60 mm stroke fits shallow guards and gantries. A fixed TPU bumper at each end absorbs end-of-stroke energy but never locks or holds a load - the piston drifts if air is lost. Mounting is FB flange, the rod end is female M8x1.25, and sensing needs the optional -S magnet with CMSE or DMSE switches.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED32X60
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.