Airtac TACED Guided Compact Cylinder TACED40X35S
The AirTAC Airtac TACED Guided Compact Cylinder TACED40X35S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø40mm bore and 35mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ40 mm
- Stroke35 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED40X35S
A double acting, double-rod ISO 21287 compact cylinder, the TACED40X35S pushes a rod out of both covers, so the 40 mm bore delivers an identical 571.8 N at 0.5 MPa (800.5 N at 0.7 MPa) in each direction - no push/pull mismatch to design around. Twin guide rods on the yoke keep the tooling square and carry side load, while the fixed TPU bumper at each end absorbs end-of-stroke shock. Running on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), it cycles at 30-500 mm/s across a -20 to +70 C range.
The hard-anodized aluminium body with an S45C hard-chrome-plated rod saves roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it drops into tight jigs and guarded gantries. This S-coded version carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches can be slid onto the body for end-of-stroke sensing. For sizing: at 0.5 MPa plan on about 343 N (roughly 35 kg) of usable work, and with a 2:1 margin it lifts about 29 kg vertically.
Airtac TACED Guided Compact Cylinder TACED40X35S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED40X35S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED40X35S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 40 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED40X35S Is Used
Clamping fixture on a CNC machining center
The 35 mm stroke clamps and releases aluminum housings in a dedicated jig, with 571.8 N holding force identical on clamp and unclamp because the rod exits both covers.
Push-off station on a packaging line
Twin guide rods keep the pusher plate square as it nudges cartons sideways off the belt at 30-500 mm/s, no external guide needed.
Position-verified test station
With the fitted -S magnet, CMSE or DMSE switches confirm extend and retract on an electronics leak-test fixture, cutting cycle time on short 35 mm moves.
Is the Airtac TACED Guided Compact Cylinder TACED40X35S the Right Cylinder?
At 571.8 N per side at 0.5 MPa, the 40 mm bore sits between the 32 mm (345.6 N) and 50 mm (881.2 N) classes - step down for lighter gripper plates, up if you need over 800 N. Because it is a through-rod design, force is equal both ways, so the same figure applies to the return stroke. Note that the piston drifts if air is lost; for a held load add a rod lock or pilot check valve. The female M8x1.25 rod thread and 1/8" PT ports suit standard fittings, FB flange mounting is available, and the -S magnet on this model enables CMSE / DMSE switch mounting. Strokes to 100 mm are standard; anything beyond is made to order.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED40X35S FAQ
Yes - the double-rod design exposes the rod-side area on both sides, so force is equal both ways: 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa, with a maximum of 116.6 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the bore 40 mm cylinder uses 1/8" ports with a female M8x1.25 rod thread.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and fixed TPU bumpers at both ends absorb end-of-stroke energy. This model carries the optional -S magnet, so CMSE / DMSE reed or solid-state switches mount directly in the body slots. FB flange mounting is available, and the twin guide rods keep the load non-rotating.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED40X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.