Airtac TACED Guided Compact Cylinder TACED40X75
The AirTAC Airtac TACED Guided Compact Cylinder TACED40X75 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø40mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ40 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED40X75
Double acting and double rod, the TACED40X75 pushes a rod out of BOTH covers, so its 40 mm bore delivers 571.8 N in each direction at 0.5 MPa (800.5 N at 0.7 MPa) because both sides work on the rod-side area. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide. Speed range is 30-500 mm/s over an operating pressure of 0.15-1.0 MPa (22-145 psi).
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why this 75 mm stroke unit drops into tight jigs, guarding and gantries. A fixed TPU bumper at each end absorbs end-of-stroke shock, and the hard-anodized aluminium body with an S45C hard-chrome plated 12 mm rod resists wear in daily duty. For sizing, plan on roughly 343 N of usable force at 0.5 MPa, which lifts about 29 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED40X75 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED40X75 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED40X75
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 40 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED40X75 Is Used
CNC fixture clamping
The 571.8 N through-rod force clamps a machined aluminium housing from both sides of a fixture, and the twin guide yoke keeps the clamp pad square to the datum.
Packaging line pusher
A 75 mm stroke kicks cartons sideways on a conveyor at up to 500 mm/s, with the TPU bumpers softening each end stop inside the guard space.
Lab sample press
About 29 kg of vertical lift capacity with margin suits a small bench-top sample press where the compact body must fit under a low frame beam.
Is the Airtac TACED Guided Compact Cylinder TACED40X75 the Right Cylinder?
At 571.8 N per side, bore 40 sits between the 32 mm (345.6 N) and 50 mm (881.2 N) TACED frames, so step down for lighter clamping or up when the part mass grows. Remember the piston drifts if air is lost - it never holds position - so add a rod lock or pilot check valve where a load must stay put. FB flange mounting, a female M8x1.25 rod thread and a PT 1/8" port come as standard; add the optional -S magnet if you need CMSE / DMSE switch feedback, and order G thread instead of PT for European plumbing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED40X75 FAQ
Yes. Because a rod exits both covers, both strokes work on the rod-side area, so output is equal both ways: 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa, with a maximum of 116.6 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) and speed runs 30-500 mm/s.
The ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Sensing needs the optional -S magnet code: with it, CMSE or DMSE switches mount in the body slots; without -S there is no magnet, so no switch can be read.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED40X75
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.