Airtac TACED Guided Compact Cylinder TACED40X75S
The AirTAC Airtac TACED Guided Compact Cylinder TACED40X75S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø40mm bore and 75mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ40 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED40X75S
A double acting, double rod compact cylinder built to ISO 21287, the TACED40X75S pushes a 12 mm rod out of both covers, so the 40 mm bore delivers the same 571.8 N at 0.5 MPa (800.5 N at 0.7 MPa) in either direction. Twin guide rods on the yoke keep the tooling from rotating and carry side load, so a gripper or press plate stays square without an external guide. The -S code on this model means the magnet is fitted, and CMSE / DMSE reed or solid-state switches can be clipped straight onto the body slots.
The hard-anodized aluminium body is about 50% shorter in mounting length than an ISO 15552 profile cylinder, which is why it drops into tight jigs, guarding and gantries where a full-length body will not fit. A fixed TPU bumper at each end absorbs end-of-stroke shock, the S45C hard-chrome rod resists wear, and in practical terms you can plan on roughly 343 N of real work at 0.5 MPa, or lift about 29 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED40X75S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED40X75S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED40X75S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 40 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED40X75S Is Used
Pick-and-place gantry slides
The 75 mm stroke and equal 571.8 N thrust both ways suit a horizontal shuttle on an electronics assembly gantry, where the twin guide rods keep the end plate from twisting as it reverses at up to 500 mm/s.
Bench press and marking jigs
With about 343 N of usable work force at 0.5 MPa, this bore stamps date codes or seats small bearings on a workshop press fixture, and the short ISO 21287 body fits under a low gantry frame.
Position-monitored clamping
Because the -S magnet is fitted, CMSE or DMSE switches confirm open and closed positions on a fixture clamp for a CNC pallet changer, with the 1/8" PT ports plumbed from either cover.
Is the Airtac TACED Guided Compact Cylinder TACED40X75S the Right Cylinder?
At 571.8 N per side, the 40 mm bore sits between the 32 mm (345.6 N) and the 50 mm (881.2 N) double-rod units, so pick 32 mm for lighter clamping and step to 50 mm when the load grows. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must be held. FB flange mounting and PT ports suit fixed jig installations, and the fitted -S magnet means CMSE / DMSE switches work without reordering.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED40X75S FAQ
Yes. The double rod design means both sides of the 40 mm piston see the rod-side area, so output is equal both ways: 571.8 N at 0.5 MPa, 800.5 N at 0.7 MPa, and up to 116.6 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi) with a 1.5 MPa (215 psi) proof pressure, and speed runs 30-500 mm/s.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end to absorb end-of-stroke energy. The fitted -S magnet accepts CMSE / DMSE switches in the body slots. For exact installed dimensions, confirm from the datasheet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED40X75S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.