Airtac TACED Guided Compact Cylinder TACED40X80
The AirTAC Airtac TACED Guided Compact Cylinder TACED40X80 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø40mm bore and 80mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ40 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM8×1.25
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED40X80
A double acting, double-rod compact cylinder built to ISO 21287, the TACED40X80 pushes a 40 mm bore through an 80 mm stroke with a rod leaving both covers. Because both chambers see the rod-side area, output is 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa in either direction - no push/pull mismatch to design around. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide.
The hard-anodized aluminium body with an S45C hard-chrome rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, from -20 to +70 C. In practice, plan on roughly 343 N (about 35 kg of force) of usable work at 0.5 MPa, which lifts around 29 kg vertically with a 2:1 margin. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and a fixed TPU bumper at each end absorbs end-of-stroke shock.
Airtac TACED Guided Compact Cylinder TACED40X80 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED40X80 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø40 mm |
| Stroke | 80 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø40mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 572 N |
| 0.7 MPa | 800 N |
| Max (@1.0 MPa) | 117 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED40X80
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 40 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED40X80 Is Used
Symmetric press-fit station
The equal 571.8 N push and pull lets one TACED40X80 seat a bearing bush then withdraw the arbor at the same force, with the twin guide yoke keeping the punch square over the 80 mm stroke.
Bidirectional gate diverter
A rod at both covers drives a conveyor pusher from either end of its travel at 800.5 N at 0.7 MPa, so the same cylinder can divert cartons left or right without reversing plumbing logic.
Non-rotating gripper jaw
Twin guide rods carry the side load of a two-jaw gripper on a robotic pick cell, holding plastic housings steady at about 35 kg of usable clamping force while the compact body fits the tight end-of-arm envelope.
Is the Airtac TACED Guided Compact Cylinder TACED40X80 the Right Cylinder?
At 571.8 N per direction, the 40 mm bore sits between the 32 mm (345.6 N) and 50 mm (881.2 N) classes - step down for lighter pick-and-place, up for heavier clamping. The 80 mm stroke is within the standard range for this bore, so no made-to-order build is needed. This version has no magnet: order the -S code if you need CMSE or DMSE switch positioning. Mounting is FB flange, the rod end is female M8x1.25, and the port is 1/8" PT. Note the piston drifts if air is lost - add a rod lock or pilot check valve where a load must be held.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED40X80 FAQ
Yes - the double-rod design exposes the rod-side area on both sides, so output is 571.8 N at 0.5 MPa and 800.5 N at 0.7 MPa in each direction. At 1.0 MPa the maximum is 116.6 kgf. Operating range is 0.15-1.0 MPa (22-145 psi) with 30-500 mm/s speed.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end that decelerates the piston at end of stroke - it is not adjustable and never holds a load. Position sensing needs the optional -S magnet code; this unit has no magnet, so CMSE or DMSE switches only work on the -S version.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED40X80
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.