Airtac TACED Guided Compact Cylinder TACED50X25
The AirTAC Airtac TACED Guided Compact Cylinder TACED50X25 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø50mm bore and 25mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ50 mm
- Stroke25 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED50X25
The TACED50X25 is a double acting, double-rod compact cylinder built to the ISO 21287 short-body format. A rod exits both covers, so the 50 mm bore delivers the same 881.2 N at 0.5 MPa (1233.7 N at 0.7 MPa) in either direction - there is no push/pull imbalance to design around. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide.
The hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which makes this a strong fit for tight jigs, guarding and gantry tooling. For sizing, treat roughly 529 N (about 54 kgf) as the usable working force at 0.5 MPa, or plan vertical lifts of about 45 kg with a 2:1 margin. The 25 mm stroke suits short approach-and-clamp moves, and a fixed TPU bumper at each end absorbs end-of-stroke shock. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, fluid filtered to 40 um.
Airtac TACED Guided Compact Cylinder TACED50X25 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED50X25 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø50 mm |
| Stroke | 25 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø50mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 881 N |
| 0.7 MPa | 1234 N |
| Max (@1.0 MPa) | 180 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED50X25
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 50 | Bore size in mm. |
| ×25 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED50X25 Is Used
Fixture clamping on a CNC pallet
The 25 mm stroke clamps a machined housing into a drill jig, with 881.2 N holding equally on extend and retract so the part seats square every cycle.
Two-sided gripper for pick-and-place
A rod exits both covers, so one cylinder can drive opposing gripper fingers on a robot end effector handling aluminium castings up to about 45 kg with a 2:1 lift margin.
Short-stamp marking press
The non-rotating twin guide yoke keeps a date-code stamp die from twisting, and the compact body fits inside a cramped printing station where a full-length cylinder will not.
Is the Airtac TACED Guided Compact Cylinder TACED50X25 the Right Cylinder?
At 50 mm bore this sits between the 40 mm TACED (571.8 N at 0.5 MPa) and the 63 mm TACED (1458.1 N at 0.5 MPa) - choose down if 571.8 N covers your clamp, up if you need over 1 kN. Because force is equal both ways, size the return stroke with the same 881.2 N figure. Remember the piston will drift if air is lost, so add a rod lock or pilot check valve for a held load. The rod end is a female M10x1.5 thread and the port is 1/8" PT. If you need position sensing, order the -S variant to enable CMSE / DMSE switches; the plain TACED50X25 carries no magnet.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED50X25 FAQ
Yes - the double-rod design means both sides see the rod-side area, so force is equal extending and retracting: 881.2 N at 0.5 MPa and 1233.7 N at 0.7 MPa in each direction. The maximum rating for the 50 mm bore is 179.7 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, and speed range is 30-500 mm/s.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight jigs and guarding. End-of-stroke shock is absorbed by a fixed TPU bumper at each cover. For sensing, order the optional -S magnet version, which allows CMSE or DMSE switches along the body; the standard TACED50X25 code has no magnet fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED50X25
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.