Airtac TACED Guided Compact Cylinder TACED63X40
The AirTAC Airtac TACED Guided Compact Cylinder TACED63X40 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 40mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke40 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X40
A double acting, double-rod ISO 21287 compact cylinder, the TACED63X40 pushes a 63 mm bore through a 40 mm stroke with a rod leaving both covers. Because both chambers see the rod-side area, output is identical in each direction: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa. Twin guide rods on the yoke stop the tooling rotating and carry side load, so a gripper or press plate stays square without an external guide.
The hard-anodized aluminium body with an S45C hard-chrome rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s, -20 to +70 C, with a fixed TPU bumper at each end. In practice, plan on roughly 875 N (about 89 kg) of usable work at 0.5 MPa, which lifts about 44 kg vertically with a 2:1 margin. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and the optional -S magnet enables CMSE / DMSE switches.
Airtac TACED Guided Compact Cylinder TACED63X40 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X40 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 40 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X40
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X40 Is Used
Symmetric press-fit station
The equal 1458.1 N output in both directions suits a CNC fixture that presses bearings home on the advance stroke and ejects the finished part on the return, with the twin guide yoke keeping the punch square.
Pallet-stacker clamp arms
A 40 mm stroke is enough to grip and release stacked totes on an AGV lifting deck, and the non-rotating guide rods stop the clamp pads twisting under offset loads.
Bidirectional conveyor stopper
A packaging line pop-up stop that must raise and lower with the same force benefits from the through-rod design, with the optional -S magnet feeding a CMSE switch to confirm up position.
Is the Airtac TACED Guided Compact Cylinder TACED63X40 the Right Cylinder?
At 1458.1 N per side at 0.5 MPa, the 63 mm bore sits between the 50 mm bore (881.2 N) and the 80 mm bore (2356.2 N) - pick 50 mm for lighter clamping, 80 mm when you need over 2300 N. The 40 mm stroke is well inside the 250 mm standard range for this bore. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve for a held load. Order the -S code if you need position sensing with CMSE / DMSE switches; without it there is no magnet. Mounting is FB flange, and the female rod thread is M10x1.5 with a 1/8" PT port.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X40 FAQ
Yes - the double rod means both sides work on the rod-side area, so output is equal either way: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s.
It is an ISO 21287 compact build whose short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a fixed TPU bumper at each end and FB flange mounting. Sensors are possible only if you order the optional -S magnet; without that code no magnet is fitted, so CMSE / DMSE switches cannot be used.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X40
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.