Airtac TACED Guided Compact Cylinder TACED63X70
The AirTAC Airtac TACED Guided Compact Cylinder TACED63X70 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 70mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke70 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X70
A double acting, double-rod ISO 21287 compact cylinder, the TACED63X70 pushes a rod out of both covers, so the 63 mm bore delivers an identical 1458.1 N in each direction at 0.5 MPa (2041.3 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without any external guide. The fixed TPU bumper at each end absorbs end-of-stroke shock.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight machine frames and guarded cells. The hard-anodized aluminium body carries a hard-chrome plated S45C rod, running on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi) and 30-500 mm/s. As a planning figure, treat roughly 875 N (about 89 kg) as the usable working force at 0.5 MPa, which corresponds to lifting about 74 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED63X70 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X70 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X70
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X70 Is Used
Symmetric press-fit station
The equal 1458.1 N force in both directions lets one TACED63X70 press a bearing into a housing on the advance and eject the finished part on the return, with the twin guide yoke keeping the punch square.
Pick-and-place gripper on a robot arm
Non-rotating twin guide rods hold gripper jaws aligned on automotive bracket transfer, while the 70 mm stroke opens and closes over the part at 30-500 mm/s.
Vertical lift-and-lower module
With about 74 kg of vertical lift capacity at a 2:1 margin, the double-rod bore 63 unit raises and lowers small pallet trays in a packaging cell, the TPU bumper softening both stroke ends.
Is the Airtac TACED Guided Compact Cylinder TACED63X70 the Right Cylinder?
At 1458.1 N per direction, the 63 mm bore sits between the 50 mm bore (881.2 N) and the 80 mm bore (2356.2 N) in the TACED range - step down when the load is lighter, step up for heavier clamping. The 70 mm stroke is a standard length for this bore. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must stay held. Mounting is FB flange; add the optional -S magnet to the order code if CMSE / DMSE switch position sensing is wanted - without -S there is no magnet in the piston.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X70 FAQ
Yes - the double-rod design exposes the rod-side area on both sides, so output is equal each way: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the rod end carries a female M10x1.5 thread with a 1/8" PT port.
It is built to ISO 21287, the short-body compact standard, saving about 50% of the mounting length of an ISO 15552 profile cylinder - useful inside guards and tight gantries. A fixed TPU bumper at each end absorbs end-of-stroke energy. Sensing is possible only if you order the optional -S magnet version, which accepts CMSE / DMSE switches; the plain TACED63X70 has no magnet fitted.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X70
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.