Airtac TACED Guided Compact Cylinder TACED63X90S
The AirTAC Airtac TACED Guided Compact Cylinder TACED63X90S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø63mm bore and 90mm stroke, 1/8" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ63 mm
- Stroke90 mm
- Port size1/8"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM10×1.5
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED63X90S
A double acting, double-rod compact cylinder built to ISO 21287, the TACED63X90S pushes a 16 mm rod out of both covers, so the force is identical in each direction: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa on the rod-side area. Twin guide rods on the yoke stop the tooling from rotating and take side load, so a gripper or press plate stays square without an external guide. The -S code on this model means the magnet is fitted, ready for CMSE / DMSE reed or solid-state switches.
The hard-anodized aluminium body with a roller-burnished bore carries an S45C hard-chrome plated rod, and a fixed TPU bumper at each end absorbs end-of-stroke shock. The short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it slots into tight jigs and gantries. In practice, plan on roughly 875 N of usable push at 0.5 MPa, which lifts about 74 kg vertically with a 2:1 margin - enough to match a real part weight before you commit.
Airtac TACED Guided Compact Cylinder TACED63X90S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED63X90S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø63 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/8" |
| Rod thread | M10×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø63mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 1458 N |
| 0.7 MPa | 2041 N |
| Max (@1.0 MPa) | 297 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED63X90S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 63 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED63X90S Is Used
Dual-side stamping press
A rod exits both covers, so one cylinder can mark or clinch on alternating faces of an aluminium housing with 1458.1 N at 0.5 MPa each way, no re-plumbing between strokes.
Symmetric pick-and-place gripper
Equal force in both directions plus the non-rotating twin guide yoke keeps a robotic gripper jaw square on PCB trays at 30-500 mm/s, with CMSE switches confirming grip via the fitted magnet.
Vertical lift-and-lower module
With about 74 kg of vertical lift capacity at a 2:1 margin, the 63 mm bore raises and lowers a die cart clamp in a press shop; a pilot check valve holds it if air drops.
Is the Airtac TACED Guided Compact Cylinder TACED63X90S the Right Cylinder?
At 1458.1 N both ways, this 63 mm bore sits between the 50 mm size (881.2 N at 0.5 MPa) and the 80 mm size (2356.2 N at 0.5 MPa), so pick down when the load is under 800 N and up when you need over 1500 N. The 90 mm stroke is within the 250 mm standard range for this bore. Remember the piston drifts if air is lost - add a rod lock or pilot check valve where a load must stay put. FB flange mounting is available, and the fitted -S magnet lets you add CMSE / DMSE switches for end-of-stroke signals.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED63X90S FAQ
Yes - the double-rod design exposes the rod-side area on both faces, so output is equal each way: 1458.1 N at 0.5 MPa and 2041.3 N at 0.7 MPa, with a maximum of 297.4 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 90 mm stroke is within the 250 mm standard limit for this bore.
The compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it fits shallow guards and tight gantry frames. A fixed TPU bumper at each end decelerates the piston at the ends of stroke, and the piston will drift if air is lost - use a rod lock or pilot check valve for held loads. This model carries the optional -S magnet, so CMSE / DMSE switches mount directly on the body slots; FB flange mounting is also offered.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED63X90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.