Airtac TACED Guided Compact Cylinder TACED80X35
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X35 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 35mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke35 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X35
A double acting, double-rod compact cylinder built to ISO 21287, the TACED80X35 pushes a 20 mm rod out of both covers, so the 80 mm bore delivers an identical 2356.2 N in each direction at 0.5 MPa (3298.7 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without an external guide. The hard-anodized aluminium body pairs with an S45C hard-chrome-plated rod, and a fixed TPU bumper sits at each end of the 35 mm stroke.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight press fixtures and gantries. For sizing, treat roughly 1414 N (about 0.6 of the 0.5 MPa rating) as the usable working force, which corresponds to lifting about 120 kg vertically with a 2:1 margin. Air supply is 0.15-1.0 MPa (22-145 psi), speed runs 30-500 mm/s, and ports are 1/4" PT with an M12x1.75 female rod thread.
Airtac TACED Guided Compact Cylinder TACED80X35 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X35 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 35 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X35
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×35 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X35 Is Used
Press fixture clamping
The 2356.2 N equal bidirectional force clamps automotive brackets in a machining fixture, then retracts with the same force to clear the part.
Heavy part transfer gripper
Twin guide rods keep the jaws square while the 80 mm bore grips cast housings on a robot load station, with about 120 kg vertical-lift margin for sizing.
Short-stamp marking head
The 35 mm stroke and compact body, roughly 50% shorter in mounting length than an ISO 15552 profile cylinder, fit a date-code stamp head under a low guard.
Is the Airtac TACED Guided Compact Cylinder TACED80X35 the Right Cylinder?
At 80 mm bore this is a high-force size: 2356.2 N both ways at 0.5 MPa. Step down to the 63 mm bore (1458.1 N at 0.5 MPa) for lighter clamping, or up to the 100 mm bore (3769.9 N at 0.5 MPa) when the tooling needs more push. Remember the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must stay held. FB flange mounting suits fixed plates, and the optional -S magnet enables CMSE / DMSE switches; without -S no magnet is fitted.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X35 FAQ
Yes. Because a rod exits both covers, both sides work on the rod-side area, so output is equal both ways: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/4" PT ports take air filtered to 40 um.
It is an ISO 21287 compact cylinder with a hard-anodized aluminium body and S45C hard-chrome rod, saving about 50% of the mounting length of an ISO 15552 profile cylinder. A fixed TPU bumper at each end absorbs end-of-stroke energy but never locks or holds a load. FB flange mounting is available, the rod end is M12x1.75 female thread, and position sensing requires the optional -S magnet ordered with CMSE / DMSE switches; this non-S model carries no magnet.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X35
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.