Airtac TACED Guided Compact Cylinder TACED80X50
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X50 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 50mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke50 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X50
A double acting, double-rod compact cylinder built to ISO 21287, the TACED80X50 pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an identical 2356.2 N at 0.5 MPa (3298.7 N at 0.7 MPa) in either direction. Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without an external guide. A fixed TPU bumper at each end absorbs end-of-stroke energy.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight machine frames and gantries. In practice, plan on roughly 1414 N (about 144 kgf) of real work at 0.5 MPa rather than the full rating, which is enough to lift about 120 kg vertically with a 2:1 margin. The hard-anodized aluminium body carries a roller-burnished bore, the S45C rod is hard-chrome plated, and 1/4" ports feed air filtered to 40 um at 0.15-1.0 MPa (22-145 psi).
Airtac TACED Guided Compact Cylinder TACED80X50 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X50 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X50
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X50 Is Used
Synchronous press platen
The through-rod drives a platen from both covers with an equal 2356.2 N up and down at 0.5 MPa, while the twin guide yoke keeps the die square over the 50 mm working stroke.
Pallet-stacking lift assist
With about 120 kg of vertical lift capacity at a 2:1 margin, the 80 mm bore raises stacked cartons between conveyor levels, and the short body fits under low guard rails.
Case clamp on a cartoner
Equal force in both directions clamps folding cartons symmetrically at up to 500 mm/s, and the non-rotating yoke holds the clamp pad aligned without external guides.
Is the Airtac TACED Guided Compact Cylinder TACED80X50 the Right Cylinder?
At 2356.2 N per side, this 80 mm unit sits between the 63 mm TACED (1458.1 N at 0.5 MPa) and the 100 mm TACED (3769.9 N at 0.5 MPa); step down for lighter clamping or up for heavier press work. It does not hold position when air is lost - the piston drifts - so add a rod lock or pilot check valve for a held load. This code has no magnet; order the optional -S version if you need CMSE / DMSE switch position sensing, and choose FB flange, CA/CB/CR or FTC mounting to suit the machine.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X50 FAQ
Yes - the double-rod design exposes the rod-side area on both sides, so output is equal both ways: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, and the 1/4" ports take air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, and FB flange or CA/CB/CR/FTC mounts adapt it to the frame. A fixed TPU bumper at each cover absorbs end-of-stroke energy but is not adjustable and never locks or brakes a load. This version has no magnet; the optional -S code adds one so CMSE / DMSE switches can report position.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.