Airtac TACED Guided Compact Cylinder TACED80X50S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X50S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 50mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke50 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X50S
A double acting, double-rod compact cylinder built to the ISO 21287 short-body format, the TACED80X50S pushes a 20 mm rod out of BOTH covers, so the 80 mm bore delivers an identical 2356.2 N in each direction at 0.5 MPa (3298.7 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without an external guide. The hard-anodized aluminium body with S45C hard-chrome plated rod runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), 30-500 mm/s.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and press frames. For sizing, treat roughly 1414 N (about 60% of the 0.5 MPa rating) as the practical working force; in vertical terms that is a lift of about 120 kg with a 2:1 margin. This -S model carries the optional magnet, so CMSE / DMSE switches can be fitted for end-of-stroke sensing, and a fixed TPU bumper at both ends absorbs stroke-end shock.
Airtac TACED Guided Compact Cylinder TACED80X50S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X50S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 50 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X50S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×50 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X50S Is Used
Pneumatic press head
The 2356.2 N both-ways force and non-rotating twin guide yoke keep a forming or staking tool square on the workpiece through the 50 mm stroke, with no external guide needed.
Heavy clamp fixture
On a machining-centre fixture, the equal 2356.2 N clamp in either direction holds steel parts; the -S magnet with a DMSE switch confirms clamped position to the PLC.
Lift-and-lower ejector
The double rod pushes and pulls with identical force, so an ejector plate on a packaging line lifts about 120 kg vertically with margin, retracting with the same authority.
Is the Airtac TACED Guided Compact Cylinder TACED80X50S the Right Cylinder?
At 80 mm bore this sits near the top of the TACED range: 2356.2 N per direction at 0.5 MPa versus 1458.1 N for the 63 mm and 3769.9 N for the 100 mm. If your press or clamp needs less than about 1450 N, step down to the 63 mm; above 2350 N go to the 100 mm. The 50 mm stroke is well inside the 300 mm standard limit for this bore, so no made-to-order stroke is needed. Note the piston drifts if air is lost - for a held load add a rod lock or pilot check valve. FB flange mounting and the -S magnet for CMSE / DMSE switches are the usual add-ons here.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X50S FAQ
Yes - the double-rod design means both directions work on the rod-side area, so force is equal either way: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/4" port suits the 80 mm bore. The female rod thread is M12x1.75.
The ISO 21287 compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which is why it fits shallow press frames and gantries. This -S version includes the optional magnet, so CMSE or DMSE reed / solid-state switches mount directly in the body slots. A fixed TPU bumper at each end absorbs stroke-end energy; it is not adjustable and does not hold the load if air is lost.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X50S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.