Airtac TACED Guided Compact Cylinder TACED80X70
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X70 is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 70mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke70 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X70
The TACED80X70 is a double acting, double rod compact cylinder built to the ISO 21287 short-body format. A 20 mm rod exits both covers, so the 80 mm bore delivers the same 2356.2 N at 0.5 MPa (3298.7 N at 0.7 MPa) in either direction - ideal for push-pull tooling that must behave identically on both strokes. Twin guide rods on the yoke stop the load rotating and take side load, so a gripper or press plate stays square without an external guide. Air supply is 0.15-1.0 MPa (22-145 psi) with speed from 30-500 mm/s.
The hard-anodized aluminium body with an S45C hard-chrome plated rod shrinks the mounting length by roughly 50% versus an ISO 15552 profile cylinder, letting the 70 mm stroke fit inside tight guards and gantry frames. A fixed TPU bumper at each end absorbs end-of-stroke shock. For a vertical application, halving the 0.5 MPa force leaves about 120 kg of usable lift capacity - enough headroom to raise a real part weight with margin. Note that the piston drifts if air is lost, so add a rod lock or pilot check valve where a load must be held.
Airtac TACED Guided Compact Cylinder TACED80X70 Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X70 |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X70
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X70 Is Used
Push-pull press fixture
Equal 2356.2 N force in both directions lets one 80 mm cylinder press a bearing home on the out-stroke and eject the part on the return, with the twin guide yoke keeping the punch aligned.
Pallet-stacker clamp arm
A 70 mm stroke closes clamp arms on stacked cartons; the non-rotating twin rods stop the arm twisting under offset loads, and about 120 kg of usable vertical capacity covers lifting the clamped load.
Reciprocating transfer slide
The through-rod drives a shuttle table both ways at identical speed and force between hard stops, with the fixed TPU bumpers taking the end-of-stroke shock at 30-500 mm/s.
Is the Airtac TACED Guided Compact Cylinder TACED80X70 the Right Cylinder?
At 2356.2 N per side at 0.5 MPa, the 80 mm bore sits between the 63 mm (1458.1 N) and 100 mm (3769.9 N) double-rod sizes - step down for lighter clamping, up for heavy press work. The 70 mm stroke is within the standard range for this bore. Ports are 1/4" (PT thread as ordered), the rod end carries a female M12x1.75 thread, and FB flange or CA/CB/CR/FTC mountings can be specified. This version has no magnet; order the -S code if you need CMSE / DMSE switch sensing.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X70 FAQ
Yes - because a rod exits both covers, both strokes work on the rod-side area of the 80 mm bore: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, equal push and pull. Peak output at 1.0 MPa reaches 480.5 kgf. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C on air filtered to 40 um.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body cuts mounting length by about 50% compared with an ISO 15552 profile cylinder, so it slots into short machine envelopes. Each end has a fixed TPU bumper for end-of-stroke deceleration. Sensing is not included on this model: the magnet is the optional -S code, which then accepts CMSE / DMSE reed or solid-state switches along the body's magnet slots.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X70
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.