Airtac TACED Guided Compact Cylinder TACED80X90S
The AirTAC Airtac TACED Guided Compact Cylinder TACED80X90S is a genuine double acting, double rod, non-rotating ISO 21287 compact air cylinder with a Ø80mm bore and 90mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder. Twin guide rods keep the tooling from rotating.
- BoreØ80 mm
- Stroke90 mm
- Port size1/4"
- Acting typeDouble acting, double rod, non-rotating
- Rod threadM12×1.75
- CushionFixed TPU bumper (both ends)
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac TACED Guided Compact Cylinder TACED80X90S
A double acting, double-rod ISO 21287 compact cylinder, the TACED80X90S pushes a 20 mm rod out of both covers, so the 80 mm bore delivers an identical 2356.2 N in each direction at 0.5 MPa (3298.7 N at 0.7 MPa). Twin guide rods on the yoke stop the tooling rotating and carry side load, keeping a gripper or press plate square without an external guide. Air supply is 0.15-1.0 MPa (22-145 psi) and speed runs 30-500 mm/s.
The hard-anodized aluminium body with an S45C hard-chrome rod is about 50% shorter in mounting length than an ISO 15552 profile cylinder, so it slots into tight press fixtures and gantry frames. This -S model carries the optional magnet, so CMSE / DMSE switches can be fitted for end-of-stroke signalling. A fixed TPU bumper sits at both ends, and since the 2356.2 N rating is rod-side area, plan on roughly 1414 N of real work at 0.5 MPa - enough to lift about 120 kg vertically with a 2:1 margin.
Airtac TACED Guided Compact Cylinder TACED80X90S Technical Specifications
| Model | Airtac TACED Guided Compact Cylinder TACED80X90S |
|---|---|
| Series | TACED compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø80 mm |
| Stroke | 90 mm |
| Acting type | Double acting, double rod, non-rotating |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 100 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating; guide rods: stainless steel (Ø12-40) / S45C (larger). Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used). Twin guide rods carry the side load and stop the tooling rotating.
Model Code: Airtac TACED Guided Compact Cylinder TACED80X90S
| TACED | ISO 21287 compact cylinder (double-rod non-rotating (twin-guide yoke)). |
|---|---|
| 80 | Bore size in mm. |
| ×90 | Stroke length in mm. |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Where the Airtac TACED Guided Compact Cylinder TACED80X90S Is Used
Press fixture clamping
The equal 2356.2 N clamp and release force on a 90 mm stroke suits stamping and welding fixtures where the part must be gripped and withdrawn with identical force.
Palletizing pusher arms
Twin guide rods keep the pusher plate square under side load while moving cartons on a conveyor line, with CMSE switches confirming each stroke end.
Dual-side test actuator
A rod exiting both covers lets one 80 mm bore drive a load or a gauge from either side in a leak or endurance test rig, no re-plumbing between cycles.
Is the Airtac TACED Guided Compact Cylinder TACED80X90S the Right Cylinder?
At 2356.2 N per direction at 0.5 MPa, the 80 mm bore sits between the 63 mm (1458.1 N) and the 100 mm (3769.9 N) - step down for lighter clamping, up for heavy die handling. The 90 mm stroke is within the 300 mm standard range for this bore, so no made-to-order build is needed. Choose FB flange, CA, CB, CR or FTC mounting to suit the frame, and remember the rod end is a female M12x1.75 thread. If the load must stay put when air is lost, add a rod lock or pilot check valve - this cylinder drifts without one.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Short stroke fits the compact body
- ✓ Port/thread type (PT / G)
- ✓ Add -S if you need the magnet for sensors
- ✓ Rod type (female / male B) & mount (FA/LB/CA)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Compact body: keep the stroke short and avoid side load on the rod.
- check Do not dismantle the threaded front/back covers.
- check Keep speed within the rated range; the TPU bumper absorbs stroke-end energy.
- check Installation by qualified personnel per AirTAC docs.
Airtac TACED Guided Compact Cylinder TACED80X90S FAQ
Yes - the double-rod design exposes the rod-side area on both strokes, so force is equal both ways: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, and the 1/4" port depends only on the 80 mm bore.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, ideal for tight gantries and guards. The S in TACED80X90S means the optional magnet is fitted, so CMSE / DMSE reed or solid-state switches mount directly on the body slots for position feedback. A fixed TPU bumper at each end absorbs end-of-stroke energy, and FB flange, CA, CB, CR or FTC mountings are available.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac TACED Guided Compact Cylinder TACED80X90S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.