The AirTAC GFR200C06MLJF1WTK AirTAC Filter Regulator NPT1/8 is a genuine G-series filter regulator: water separation, 40 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has See datasheet ports, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
The AirTAC GFR200C06MLJF1WTK is a filter regulator: it removes water and particulate from compressed air and regulates downstream pressure in a single body. This size 200 unit is threaded NPT1/8 (1/8 in), carries the fine 5 um filter element, a manual drain on the polycarbonate (PC) bowl, a low-pressure regulator, an embedded square gauge scaled in MPa, and a built-in reverse/check valve. No mounting bracket is included (code J). It runs on compressed air only, tolerates a maximum inlet pressure of 1.0 MPa (145 psi), and is rated for -5 to 70 C in non-freezing conditions.
This is a genuine AirTAC part. The GFR family spans sizes 200, 300, 400 and 600 with port sizes from 1/8 to 1 in, plus drain choices (differential-pressure, automatic or manual), 40 um or 5 um filtration, gauge, thread and bracket options. Flow for the series is published as curves rather than a single rated figure, so ask us to confirm the sizing figures from the datasheet for your application.
| Model | GFR200C06MLJF1WTK AirTAC Filter Regulator NPT1/8 |
|---|---|
| Series | GFR200 filter regulator |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GFR200 | G-series filter regulator, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Mounting bracket included. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR200 · See datasheet · 40 µm |
|---|---|
| One size up | GFR300 |
| Add lubrication | GFC200-C0 (two-unit set) |
On a glue or sealant dispensing bench where the dispense valves are specified for reduced supply pressure, the low-pressure regulator holds a gentle setpoint while the 5 um element keeps the valve's pilot air clean.
Feeding small gripper cylinders on an assembly cell: filter and regulator in one body saves panel space on a 1/8 in air drop, and the built-in check valve blocks backflow toward the supply.
On a laboratory test stand running instruments at reduced air pressure, the square MPa gauge gives a direct readout and the manual drain lets an operator clear accumulated condensate at the end of each run.
Size and port set the capacity: the 200 size with its NPT1/8 port suits the smallest branch lines, while stepping up to sizes 300, 400 or 600 and ports from 1/4 to 1 in serves growing air demand. Drain type is a real operating choice: the manual drain here needs an operator to open it, whereas automatic and differential-pressure drains discharge condensate on their own and are orderable in the same family. Filtration is 5 um on this unit versus the 40 um standard - choose 5 um where downstream valves and cylinders need cleaner air. The embedded square gauge reads MPa; an external round gauge and psi or bar scales are options. Thread is NPT here (PT is the standard thread and G/BSPP is an orderable option), and no bracket is fitted. Because flow is published as curves rather than one rated number, send us your pressure and demand and we will confirm sizing from the datasheet before you order.
Quick checklist
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
AirTAC publishes flow for the GFR series as curves, not as a single rated figure, so we do not quote a number here. Tell us your line pressure and air demand and we will confirm the flow from the datasheet for this exact configuration before you order.
The manual drain (code M) releases collected condensate when you open it, which suits units mounted where an operator passes regularly. If the unit sits in an inaccessible spot, the same GFR family is orderable with an automatic or differential-pressure drain. Also note this is the low-pressure regulator type (code L); its exact regulation range is not published in the catalogue, so we confirm it on request.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.