The AirTAC GFR200C06MLJF2WG AirTAC Filter Regulator G1/8, 5 um is a genuine G-series filter regulator: water separation, 40 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has See datasheet ports, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
The AirTAC GFR200C06MLJF2WG is a GFR-series filter regulator: one body that removes water and particulate from compressed air and then regulates the downstream pressure. This configuration is the 200 size with a G1/8 (BSPP) port, the finer 5 um filter element (code W), a manual drain, and the low-pressure regulator type (code L). It comes with the embedded square gauge scaled in psi, no mounting bracket (code J), and no reverse/check valve fitted.
This is a genuine AirTAC part. The GFR family spans the 200, 300, 400 and 600 sizes with ports from 1/8 to 1 inch, a choice of differential-pressure, automatic or manual drains, 40 um standard or 5 um filtration, gauge and thread options, and standard or low-pressure regulator types. Maximum inlet pressure is 1.0 MPa (145 psi) and the working temperature range is -5 to 70 C, non-freezing. AirTAC publishes flow as curves rather than a single rating, so we confirm the datasheet and flow figures for your application on request.
| Model | GFR200C06MLJF2WG AirTAC Filter Regulator G1/8, 5 um |
|---|---|
| Series | GFR200 filter regulator |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GFR200 | G-series filter regulator, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Mounting bracket included. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR200 · See datasheet · 40 µm |
|---|---|
| One size up | GFR300 |
| Add lubrication | GFC200-C0 (two-unit set) |
Filtered, low-pressure regulated air feeds the pilot ports of solenoid valves on a form-fill-seal line. The 5 um element helps keep grit out of valve spools, and the square psi gauge lets the technician see the pilot setting at a glance; the manual drain is cracked open at the end of each shift.
On a light-duty clamping circuit where full line pressure is too aggressive, the low-pressure regulator type holds a gentler set pressure to the clamp cylinders while the filter section strips water and chips-carried mist from the shop air ahead of the fixture.
A bench test rig running pneumatic actuators and air-bearing fixtures needs clean, low-pressure air. This unit filters to 5 um and regulates down from the house supply, with the psi-scaled square gauge giving a clear local readout for setup and verification.
Step up through the 200, 300, 400 and 600 sizes as your flow demand grows; this unit is the 200 size with a 1/8 in G-thread (BSPP) port, so check it against your downstream air consumption before ordering. Filtration here is the finer 5 um element - choose it where downstream valves, cylinders or instruments need cleaner air, and 40 um where general protection is enough. The manual drain means the polycarbonate bowl must be emptied periodically by opening the drain; automatic and differential-pressure drains are available elsewhere in the family. The L code marks the low-pressure regulator type; its adjustment range is not published in the standard table, so confirm your set pressure with us. The gauge is the embedded square type scaled in psi, with external round gauges and MPa or bar scales available as options. Thread is G (BSPP) - PT and NPT are order options - and no mounting bracket is included in this configuration.
Because AirTAC publishes flow as curves rather than a single rated figure, we do not quote a flow number here. Ask us to confirm sizing and the datasheet figures for this exact model against your application before you order.
Quick checklist
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
AirTAC publishes flow for the GFR series as curves rather than a single rated figure, so we do not quote a flow number for this model. Tell us your application and downstream consumption, and we will confirm the flow curves and the full datasheet figures for this exact unit on request before you order.
L marks the low-pressure regulator type; its adjustment range is not published in the standard table, so confirm your required set pressure with us. M marks the manual drain: the polycarbonate bowl must be emptied periodically by opening the drain fitting. If you would rather not do that, the family also offers automatic and differential-pressure drain versions.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.