The AirTAC GFR200C08LC2WG AirTAC Filter Regulator G1/4 5 um is a genuine G-series filter regulator: water separation, 40 µm particulate filtration and balanced-type pressure regulation combined in a single body. It has See datasheet ports, a differential-pressure drain and regulates 0.15 - 0.9 MPa (20 - 130 psi). It does not lubricate — add a GL lubricator, or order the GFC two-unit set, if downstream equipment needs oil.
The AirTAC GFR200C08LC2WG is a low-pressure filter regulator: it removes water and particulate from compressed air and regulates downstream pressure in a single body. This configuration carries a G1/4 port, the finer 5 um filter element (code W), a differential-pressure drain, a metal bowl, a fitted round gauge scaled in psi, and a mounting bracket. Maximum inlet pressure is 1.0 MPa (145 psi) and the working temperature range is -5 to 70 C (non-freezing). The low-pressure (L) regulator type is intended where the controlled pressure must sit below the standard range; the exact adjustment range for this variant is not published, so ask us to confirm it.
This is a genuine AirTAC part. The GFR series spans sizes 200, 300, 400 and 600 with ports from 1/8 to 1 inch, plus drain, filter-grade, gauge, thread and bracket options. Flow for the series is published as curves rather than a single rated figure, so we confirm flow and full datasheet figures for this exact model on request.
| Model | GFR200C08LC2WG AirTAC Filter Regulator G1/4 5 um |
|---|---|
| Series | GFR200 filter regulator |
| Port size | See datasheet (PT thread) |
| Filtering grade | 40 µm |
| Regulating range | 0.15 - 0.9 MPa (20 - 130 psi) |
| Pressure type | Standard type |
| Adjusting mechanism | Balanced type |
| Fluid | Compressed air |
|---|---|
| Max. working pressure | 1.0 MPa (145 psi) |
| Temperature range | -5 to +70 °C (unfreeze) |
| Drain type | Differential-pressure drain |
| Bowl material | PC |
| Pressure gauge | Fitted — factory standard, Factory standard scale |
| Reflux valve | Not fitted |
Specifications follow the official AirTAC G-series air-preparation data. The regulating band is set by the drain type: automatic and differential-pressure drains regulate 0.15 - 0.9 MPa, a manual drain regulates 0.05 - 0.9 MPa. Standard type, regulating 0.15 - 0.9 MPa (20 - 130 psi). Air must not freeze in the unit. Flow curves, weight and outline dimensions are not published in our data set — ask us and we will confirm from the factory datasheet.
| GFR200 | G-series filter regulator, 200 body — sets the port range. |
|---|---|
| C0 | Port size See datasheet. This body offers 06 = PT1/8", 08 = PT1/4". |
| (blank) | Drain: Differential-pressure drain — this also sets the regulating band (0.15 - 0.9 MPa (20 - 130 psi)). |
| (blank) | Standard type. Blank is standard, L is the low-pressure type. |
| (blank) | Mounting bracket included. |
| (blank) | Pressure gauge fitted (blank). |
| (blank) | Gauge shape: Factory standard. C is round, F is square. |
| (blank) | Gauge scale: Factory standard. 1 is MPa, 2 is psi, 3 is bar. |
| (blank) | Filtering grade 40 µm. Only 40 µm (blank) and 5 µm (W) exist. |
| (blank) | PT thread. PT is the default; G is BSPP and T is NPT. |
| (blank) | No reverse-flow valve (the default). |
Field order is size, port, drain, type, bracket, gauge, shape, scale, grade, thread, reflux — a blank position takes the default. Example: GFR300-08 is a 300 body, PT1/4", differential drain, standard type, bracket included, gauge fitted, 40 µm, PT thread, no reflux valve.
A larger body carries a larger port and holds set pressure better as flow rises. AirTAC publishes flow only as curves, so size the body from your peak demand with headroom. The GFR600 uses an aluminium-alloy bowl; the 200, 300 and 400 bodies use PC.
| This model | GFR200 · See datasheet · 40 µm |
|---|---|
| One size up | GFR300 |
| Add lubrication | GFC200-C0 (two-unit set) |
Fixture and clamping circuits on machining centres that hold workpieces at reduced pressure, where the low-pressure regulator type gives gentle control and the 5 um element keeps the clamp cylinders clean.
Feeding forming, sealing and labelling heads on a packaging line: water and fine particulate are stripped out while one knob holds a steady, lower working pressure at the machine.
Bench setups and pilot-scale test rigs that need clean, gently regulated air at a stable low setting, with the fitted psi gauge giving a direct local readout at the point of use.
Size and port step up together with flow demand: 200 is the compact frame of the GFR range, here with a G1/4 port. This unit is fixed at 5 um filtration (the series standard element is 40 um; 5 um is the W option), drains by differential pressure, and carries a round gauge scaled in psi - embedded square gauges and MPa/psi/bar scales are the catalogue alternatives. The thread is G; PT is the standard thread and G/NPT are order options. A mounting bracket is included, and no reverse/check valve is fitted on this code. Because flow is published as curves, not a single rated figure, ask us to confirm sizing against your application before ordering.
Quick checklist
The PC bowl must not be cleaned with solvents — wipe it with a dry cloth. Without the K option, air cannot flow back through the unit. A filter regulator adds no oil to the line.
AirTAC publishes flow for the GFR series as curves, not as a single rated figure, so we do not quote a number here. Send us your application details and we will confirm the flow and the full datasheet figures for this exact model on request.
The GFR series standard element is 40 um; the W code on this model selects the finer 5 um element. Choose 5 um where downstream valves, cylinders or instruments need cleaner air, and the differential-pressure drain - the series default - handles condensate removal without a manual drain action.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Standard models usually ship in 3-4 days.
Most inquiries answered within 7-8 hours.
Send us the quantity, thread type (PT / G / NPT), gauge scale and destination. We confirm price, availability and lead time — usually within 7-8 hours.