Compact Cylinder Guide: ISO 21287 AirTAC ACE vs ACQ vs SDA
Mounting bolt square, rod thread, port and length of AirTAC ACE (ISO 21287), ACQ and SDA compact cylinders by bore, and why they are not interchangeable.
AirTAC makes three families of short-body compact cylinders that look alike but do not share mounting dimensions. ACE is built to ISO 21287. ACQ is built to JIS standards according to its AirTAC catalog. SDA is AirTAC's own compact design. Swapping one for another without checking usually means redrilling the mounting holes or changing the rod-end part.
Which family is which
| Family | Standard | Bores (mm) | Port threads | Sensors |
|---|---|---|---|---|
| ACE | ISO 21287 | 12 to 125 | PT, G | CMSE, DMSE |
| ACQ | JIS (AirTAC catalog) | 12 to 100; 125 to 160 big bore | PT, G, NPT (T) | CS1-G / CS1-J, CMSG / CMSJ and the DS1 / DMS equivalents |
| SDA | AirTAC design | 12 to 100 | PT | CS1-G / CS1-J, CMSG / CMSJ and the DS1 / DMS equivalents |
ISO 21287 covers compact cylinders with bores 20 to 100 mm. ACE Ø12, Ø16 and Ø125 follow the same design but are outside the range of the standard.
Mounting bolt square by bore
The bolt square is the distance between the four mounting screws on the cover face. This is the number that decides whether a replacement fits the existing holes.
| Bore | ACE □JB (ISO 21287) | ACQ □KB | SDA □KB | AirTAC model pages |
|---|---|---|---|---|
| Ø12 | 16 | 15.5 | 16.3 | ACE12 · ACQ12 · SDA12 |
| Ø16 | 18 | 20 | 19.8 | ACE16 · ACQ16 · SDA16 |
| Ø20 | 22 | 25.5 | 24 | ACE20 · ACQ20 · SDA20 |
| Ø25 | 26 | 28 | 28 | ACE25 · ACQ25 · SDA25 |
| Ø32 | 32.5 | 34 | 34 | ACE32 · ACQ32 · SDA32 |
| Ø40 | 38 | 40 | 40 | ACE40 · ACQ40 · SDA40 |
| Ø50 | 46.5 | 50 | 48 | ACE50 · ACQ50 · SDA50 |
| Ø63 | 56.5 | 60 | 60 | ACE63 · ACQ63 · SDA63 |
| Ø80 | 72 | 77 | 74 | ACE80 · ACQ80 · SDA80 |
| Ø100 | 89 | 94 | 90 | ACE100 · ACQ100 · SDA100 |
| Ø125 | 110 | - | - | ACE125 |
Highlighted values are not fixed by an ISO standard. Check them against the CAD model or PDF drawing of the part you are replacing before you order. ACE values for Ø20 to Ø100 are the ISO 21287 values; from Ø32 they equal the ISO 15552 bolt square of the same bore.
The common mistake: ordering an ACQ or SDA to replace an ISO 21287 compact cylinder. At Ø32 the bolt square is 32.5 mm on ACE but 34 mm on ACQ and SDA; at Ø63 it is 56.5 mm against 60 mm. The screws will not line up.
Rod threads and ports
Standard (female) rod threads and port sizes. With the male-thread rod (B in the order code) the rod thread changes; check the male-thread table on the model page.
| Bore | ACE rod | ACQ rod | SDA rod | ACE port | ACQ port | SDA port |
|---|---|---|---|---|---|---|
| Ø12 | M3×0.5 | M3×0.5 | M3×0.5 | M5 | M5 | M5 |
| Ø16 | M4×0.7 | M4×0.7 | M3×0.5 | M5 | M5 | M5 |
| Ø20 | M6×1.0 | M5×0.8 | M4×0.7 | M5 | M5 | M5 |
| Ø25 | M6×1.0 | M6×1.0 | M5×0.8 | M5 | M5 | M5 |
| Ø32 | M8×1.25 | M8×1.25 | M6×1.0 | 1/8" | 1/8" | 1/8" |
| Ø40 | M8×1.25 | M8×1.25 | M8×1.25 | 1/8" | 1/8" | 1/8" |
| Ø50 | M10×1.5 | M10×1.5 | M10×1.5 | 1/8" | 1/4" | 1/4" |
| Ø63 | M10×1.5 | M10×1.5 | M10×1.5 | 1/8" | 1/4" | 1/4" |
| Ø80 | M12×1.75 | M16×2.0 | M14×1.5 | 1/8" | 3/8" | 3/8" |
| Ø100 | M12×1.75 | M20×2.5 | M18×1.5 | 1/8" | 3/8" | 3/8" |
| Ø125 | M16×2.0 | - | - | 1/4" | - | - |
ACQ and SDA share the bolt square at Ø25, Ø32, Ø40 and Ø63, but the rod threads differ at Ø16 to Ø32 and from Ø80, so a rod-end joint for one does not always fit the other.
Body length
| Bore | ACE A | ACQ A | SDA A |
|---|---|---|---|
| Ø12 | 40 | 31.5 | 32 |
| Ø16 | 40 | 34 | 34 |
| Ø20 | 43 | 36 | 35 |
| Ø25 | 45 | 37.5 | 37 |
| Ø32 | 51 | 40 | 41.5 |
| Ø40 | 52.5 | 46.5 | 43 |
| Ø50 | 53.5 | 48.5 | 47 |
| Ø63 | 57 | 54 | 51 |
| Ø80 | 63 | 63.5 | 62 |
| Ø100 | 76 | 75 | 73 |
| Ø125 | 92 | - | - |
ACE is the same length with or without a magnet. ACQ and SDA without a magnet are shorter (for example SDA32: 31.5 mm instead of 41.5 mm), and without a magnet ACQ is 10 mm longer from 60 mm stroke. Use the drawing on the model page for the exact stroke.
Rules for swapping
- Replacing an ISO 21287 compact cylinder from any maker (Ø20 to Ø100): choose ACE. Check the length and sensor against your drawing.
- Replacing an existing ACQ or SDA: order the same family. ACQ and SDA are not ISO 21287.
- Need NPT ports on a compact cylinder: ACQ offers
T(NPT); ACE offers PT and G; SDA is PT. - Need a sensor: order the magnet version (
S) and the sensor listed on the model page. - Discontinued ACP, ASP and ATP ship as ACE, ASE and ATE: the code after the prefix stays the same.
Order code examples
ACE32X25S = ACE Ø32 × 25 mm, magnet. ACQ32X25ST = ACQ Ø32 × 25 mm, magnet, NPT ports. SDA32X25SB = SDA Ø32 × 25 mm, magnet, male rod thread. ACED / ACQD / SDAD are double rod; ACEJ / ACQJ / SDAJ have an adjustable stroke.
Frequently asked questions
Is AirTAC ACQ an ISO 21287 cylinder?
No. ACQ is built to JIS standards according to its AirTAC catalog, and its mounting bolt square differs from ISO 21287: 34 mm at Ø32 and 60 mm at Ø63, against 32.5 mm and 56.5 mm. The AirTAC ISO 21287 family is ACE.
Can SDA replace ACQ?
Only after checking. They share the bolt square at Ø25, Ø32, Ø40 and Ø63, but it differs at the other bores, the rod threads differ at several bores (Ø32: ACQ M8×1.25, SDA M6×1.0) and the lengths are not the same.
Which AirTAC compact cylinder has NPT ports?
ACQ, with T at the end of the order code. ACE is offered with PT or G ports and SDA with PT ports.
What is the bolt square of an ISO 21287 Ø50 compact cylinder?
46.5 mm, the value used by AirTAC ACE50. ACQ50 uses 50 mm and SDA50 uses 48 mm.
Have a part number, a nameplate photo or a BOM? Send it and we reply with prices and the matching AirTAC order codes within 7 hours.
Request a quote