verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote

Pneumatic Port Threads: PT (BSPT) vs G (BSPP) vs NPT

PT, G and NPT port threads compared: thread angle, taper, threads per inch and diameters from 1/8 to 1 inch, the AirTAC thread letters and which series offer which.

By AirtacDistr, authorized AirTAC export distributor · Data from official AirTAC catalogs and the cited ISO / ASME standards · Updated November 18, 2026

AirTAC parts come with three port threads that look almost the same: PT (BSPT), G (BSPP) and NPT. The thread is the last letter of the order code. Mixing them is the most common cause of leaking or seized fittings.

PT, G and NPT compared

Port thread comparison
PT (BSPT, R / Rc) G (BSPP) NPT
AirTAC code letter none (standard) G T
Standard ISO 7-1, JIS B 0203 ISO 228-1 ASME B1.20.1
Thread angle 55° 55° 60°
Form Tapered 1:16 Parallel Tapered 1:16
Seals on The thread, with tape or sealant A bonded washer or O-ring at the port face The thread, with tape or sealant

Threads per inch and diameters

ISO 7-1 / ISO 228-1 and ASME B1.20.1 values
Size PT / G TPI PT / G pitch (mm) PT / G major Ø (mm) NPT TPI NPT pitch (mm) NPT OD (mm)
1/8" 28 0.907 9.728 27 0.941 10.29
1/4" 19 1.337 13.157 18 1.411 13.72
3/8" 19 1.337 16.662 18 1.411 17.15
1/2" 14 1.814 20.955 14 1.814 21.34
3/4" 14 1.814 26.441 14 1.814 26.67
1" 11 2.309 33.249 11.5 2.209 33.40

1/8", 1/4", 3/8" and 1" have a different pitch (highlighted), so a PT or G fitting will not thread into an NPT port. At 1/2" and 3/4" the pitch is the same, 14 TPI, but the 55° and 60° thread angles still do not seal. Never mix PT and NPT.

PT and G share the pitch and diameter, so a G fitting will go into a PT port, but the parallel G thread does not seal on the thread: use a G port with a washer or O-ring, or keep PT on both sides.

M5 ports (M5×0.8) are metric. They are used on small valves and cylinders and take no thread letter.

Which AirTAC series offer which thread

Thread options in the AirTAC catalogs; each model page lists the codes it offers
Series PT G NPT (T) Source
4V solenoid valves Yes Yes Yes (not M5) 4V catalogs
SAI, SE Yes Yes - SAI, SE catalogs
SC Yes Yes - SC catalog
ACE Yes Yes - ACE catalog
ACQ Yes Yes Yes ACQ catalog
SDA Yes - - SDA catalog

Fittings and silencers: PC push-in fittings and BSL silencers are PT. For NPT ports ask for NPT fittings with your quote.

Identifying a thread you have

  1. Measure the outside diameter of the male thread with calipers and compare it with the table.
  2. Count the threads over 1 inch (25.4 mm) or use a thread gauge: 19 means PT or G 1/4" or 3/8"; 18 means NPT 1/4" or 3/8".
  3. Check the taper: a tapered thread gets wider towards the end of the fitting; a parallel G thread does not.
  4. Look at the order code on the nameplate: no letter = PT, G = G, T = NPT.

Frequently asked questions

Can I use a PT fitting in an NPT port?

No. The thread angles differ (55 degrees for PT, 60 degrees for NPT) and at 1/8, 1/4, 3/8 and 1 inch the pitch differs too, for example 19 against 18 threads per inch at 1/4 inch. The joint will leak or damage the port.

What does the G at the end of an AirTAC order code mean?

G (BSPP, ISO 228-1) parallel port thread instead of the standard PT. T means NPT. A code with no thread letter has PT ports.

How many threads per inch does 1/4 inch NPT have?

18. 1/4 inch PT and G have 19 threads per inch.

Is PT the same as BSPT?

Yes. PT is the Japanese (JIS B 0203) name for the 55 degree tapered pipe thread of ISO 7-1, also called BSPT or R / Rc.

Have a part number, a nameplate photo or a BOM? Send it and we reply with prices and the matching AirTAC order codes within 7 hours.

Request a quote