This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is ACED80X110 — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the ACED80X110 in place of this model. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD80X110
The AirTAC Airtac ACPD Double Rod Compact Cylinder ACPD80X110 is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø80mm bore and 110mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED80X110 (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke110 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- StatusDiscontinued → ACED80X110
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD80X110
A double acting compact cylinder with a rod leaving both covers, the ACPD80X110 pushes and pulls with identical force: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa in either direction, because both strokes work on the rod-side area of the 80 mm bore. The 20 mm through-rod resists rotation and side load, gives a symmetric mount, and lets the rear rod carry a sensor flag, while fixed TPU bumpers pad both ends. Speed range is 30-500 mm/s on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi).
The hard-anodized aluminium body follows the short ISO 21287 style, saving roughly 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight gantries and press fixtures. Note this model is discontinued: the current-production drop-in is the ACED80X110 (swap the P for an E), same bore, stroke and force class - confirm the ISO 21287 mounting dimensions before swapping. For sizing, plan on about 1414 N of real work at 0.5 MPa rather than the full rating, which corresponds to lifting roughly 120 kg vertically with a 2:1 margin.
Airtac ACPD Double Rod Compact Cylinder ACPD80X110 Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD80X110 |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED80X110 |
| Bore size | Ø80 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED80X110 (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD80X110
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD80X110 Is Used
Benchtop crimping press
The 2356.2 N available in both directions at 0.5 MPa suits a small bench press that crimps terminals or rivets, with the 110 mm stroke clearing the part by hand between cycles.
Reciprocating conveyor pusher
A rod on each cover lets one cylinder drive a pallet pusher on the forward stroke and return a counterweight or flag on the same shaft, keeping force equal at 3298.7 N at 0.7 MPa either way.
Gantry part ejector
The short ISO 21287-style body fits inside a machine-tool gantry where a full-length profile cylinder will not, ejecting machined housings from a fixture at up to 500 mm/s.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD80X110 with the ACED80X110
At 80 mm bore this is the second-strongest ACPD size: 2356.2 N per direction at 0.5 MPa, one step below the 100 mm bore (3681.6 N) and well above the 63 mm bore (1458.1 N). The 110 mm stroke sits inside the 300 mm maximum standard stroke for this bore, so it is a catalog item, not a made-to-order length. Choose the female M12x1.25 rod thread as coded here, or add B for a male thread. Remember the piston drifts when air is lost - add a rod lock or pilot check if the load must be held. This unit ships without a magnet; order the -S code if you need CMSE / DMSE switch positions. Since the ACPD is discontinued, order the ACED80X110 as the current replacement and verify the ISO 21287 mounting footprint.
Replacement checklist
- ✓ Current-production ACE → ACED80X110
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD80X110 FAQ
Yes - the double-rod design means both strokes use the rod-side area, so force is equal either way: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, with a maximum of 480.5 kgf at 1.0 MPa. Operating range is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, on air filtered to 40 um through the 1/4" port.
Order the ACED80X110, the current-production ISO 21287 successor made by swapping the P for an E. It matches the same 80 mm bore, 110 mm stroke and force class, and accepts the FA/FB flange, LB foot and CA/CB clevis brackets on the ISO 21287 face. Because the ACP is DIN-standard, confirm the ISO 21287 mounting dimensions before swapping. Also note the -S magnet for CMSE / DMSE switches is an option, not a default.
Related AirTAC ACE Cylinders
Request a Quote for the ACED80X110
Send us the quantity and destination. We confirm price, stock and lead time on the ACED80X110 replacement — usually within 7-8 hours.