This model is discontinued
AirTAC has phased out the MAL series. The drop-in replacement is ACED80X75S — same bore, stroke, output force, port and mounting, so it fits the same application. Simply order the ACED80X75S in place of this model. The ACE replacement is a current-production ISO 21287 compact cylinder in the same bore, stroke and force class, with a matching short body and the same mounting-accessory family, so it fits the same envelope. Confirm mounting-interface dimensions against the ACE datasheet before ordering.
Airtac ACPD Double Rod Compact Cylinder ACPD80X75S
The AirTAC Airtac ACPD Double Rod Compact Cylinder ACPD80X75S is a double acting, double rod DIN-standard tight/compact air cylinder with a Ø80mm bore and 75mm stroke, 1/4" air ports and a hard-anodized aluminium body. This model is discontinued — the current-production replacement is the ACED80X75S (ISO 21287 ACE), in the same bore, stroke and force class.
- BoreØ80 mm
- Stroke75 mm
- Port size1/4"
- Acting typeDouble acting, double rod
- Rod threadM12×1.75
- StatusDiscontinued → ACED80X75S
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac ACPD Double Rod Compact Cylinder ACPD80X75S
A double acting compact cylinder with a rod through both covers, the ACPD80X75S pushes and pulls with identical force because both strokes work on the rod-side area: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa in either direction. The 80 mm bore drives a 20 mm hard-chrome S45C rod from each end, and the through-rod resists rotation and side load while the rear rod can carry a sensor flag. This unit carries the optional -S magnet, so CMSE or DMSE reed and solid-state switches mount directly on the body.
The hard-anodized aluminium body follows the ISO 21287 short format, cutting roughly 50% of the mounting length of an ISO 15552 profile cylinder, which matters in tight gantries and guarding. A fixed TPU bumper sits at each end, speed runs 30-500 mm/s, and pressure spans 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof. Plan on about 1414 N (roughly 144 kg) of usable push at 0.5 MPa rather than the full rating, and note the model is discontinued - ACED80X75 is the current drop-in.
Airtac ACPD Double Rod Compact Cylinder ACPD80X75S Technical Specifications
| Model | Airtac ACPD Double Rod Compact Cylinder ACPD80X75S |
|---|---|
| Series | ACPD DIN compact cylinder (discontinued) |
| Replacement | ACED80X75S |
| Bore size | Ø80 mm |
| Stroke | 75 mm |
| Acting type | Double acting, double rod |
| Port size | 1/4" |
| Rod thread | M12×1.75 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACP datasheet (now discontinued). The ACED80X75S (ISO 21287) carries the same bore/stroke/force class; confirm mounting-interface dimensions against the ACE datasheet before installation. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G.
Theoretical Output Force (Ø80mm)
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 2356 N |
| 0.7 MPa | 3299 N |
| Max (@1.0 MPa) | 481 kgf |
Double-rod: a rod exits both covers, so output force is equal in both directions (rod-side area used).
Model Code: Airtac ACPD Double Rod Compact Cylinder ACPD80X75S
| ACPD | DIN compact cylinder (double-rod, discontinued). |
|---|---|
| 80 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| S | Optional built-in magnet for sensor position sensing (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
Replacement mapping (swap P for E): ACP→ACE, ASP→ASE, ATP→ATE, ACPD→ACED, ACPJ→ACEJ. ACP-family: ACP (double acting), ASP / ATP (single acting push / pull), ACPD (double rod), ACPJ (adjustable stroke).
Where the Airtac ACPD Double Rod Compact Cylinder ACPD80X75S Is Used
Reciprocating press transfer
The equal 2356.2 N force in both directions suits a pick-and-place slide on a stamping cell, where the through-rod pushes the part out and retracts the fixture with the same thrust.
Machine tool counterbalance slide
A rear rod on the 20 mm shaft can carry a sensor flag for CMSE switches, while the front rod drives a milling-machine auxiliary slide at 30-500 mm/s.
Packaging machine clamp beam
With about 120 kg of vertical lift capability at a 2:1 margin, the 80 mm double rod holds a symmetric clamp beam level across both ends of a carton sealing head.
Replacing the Airtac ACPD Double Rod Compact Cylinder ACPD80X75S with the ACED80X75S
At 75 mm stroke this sits well inside the 300 mm maximum standard stroke for the 80 mm bore, so it is a catalog item, not a made-to-order length. If 2356.2 N at 0.5 MPa is more than the job needs, the 63 mm bore delivers 1458.1 N; if you need more, the 100 mm bore reaches 3681.6 N under the same pressure. Remember the piston drifts when air is lost - add a rod lock or pilot check if the load must stay put. FA/FB flange and LB foot mountings bolt to the ISO 21287 face, and the -S magnet on this version accepts CMSE / DMSE switches. For new designs, order ACED80X75 instead and confirm the ISO 21287 mounting dimensions before swapping.
Replacement checklist
- ✓ Current-production ACE → ACED80X75S
- ✓ Same bore / stroke / force class
- ✓ Confirm ISO 21287 mounting dimensions
- ✓ Port/thread type (PT / G)
- ✓ Add -S for magnet if you need sensors
Airtac ACPD Double Rod Compact Cylinder ACPD80X75S FAQ
Because a rod exits both covers, output is equal both ways: 2356.2 N at 0.5 MPa and 3298.7 N at 0.7 MPa, on the rod-side area in each direction. Peak force at 1.0 MPa is 480.5 kgf. Operating range is 0.15-1.0 MPa (22-145 psi) with 1.5 MPa (215 psi) proof pressure, and speed is 30-500 mm/s.
No - the ACPD family is discontinued. The current-production replacement is ACED80X75, an ISO 21287 compact cylinder in the same 80 mm bore, 75 mm stroke and force class. Since the ACP is DIN-standard, confirm the ISO 21287 mounting dimensions before swapping. The fixed TPU bumpers, 1/4" ports and M12x1.75 female rod thread carry over in the same class.
Related AirTAC ACE Cylinders
Request a Quote for the ACED80X75S
Send us the quantity and destination. We confirm price, stock and lead time on the ACED80X75S replacement — usually within 7-8 hours.