Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR
The AirTAC Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR is a single acting, pull type (spring extend) pen-size mini cylinder with a Ø10mm bore and 60mm stroke. A single air port drives the pull stroke; the built-in return spring resets the rod when air is released, so only one solenoid line is needed.
- BoreØ10 mm
- Stroke60 mm
- Port sizeM5×0.8
- Acting typePull, single acting
- Rod threadM8×1.0
- ReturnSpring
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR
The AirTAC PTB10X60SR is a JIS pen-size mini cylinder configured for single-acting pull operation. Air entering the single M5x0.8 port retracts the Ø4 mm rod, while an internal spring pushes it back out upon exhaust release. This provides a fail-safe extended state during air loss, keeping your tooling safely in its home position. Delivering 23.5 N of net pull at 0.5 MPa, the return spring force is already deducted from this rating.
This 60 mm stroke variant features a built-in piston magnet for position sensing with reed or electronic switches. The slim SUS304 stainless body incorporates a fixed TPU bumper to decelerate motion at the end of travel. Because the powered stroke acts on the smaller rod-side area, this pull force is lower than a comparable push cylinder. Plan for a safe working load of roughly 14 N, accounting for seal friction and smooth travel margins.
Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR Technical Specifications
| Model | Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR |
|---|---|
| Series | PTB JIS pen-size mini cylinder |
| Bore size | Ø10 mm |
| Rod diameter | Ø4 mm |
| Stroke | 60 mm |
| Acting type | Single acting, pull type (spring extend) |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.2 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 800 mm/s |
| Return | Return spring (pull by air) |
| Max standard stroke | Up to 60 mm |
The spring holds the rod extended; applying air retracts it, and removing air lets the spring push the rod back out. Forces below are the NET spring-deducted values from the AirTAC thrust table. Confirm against the product label before installation.
Net Pull Force (Ø10mm)
| Pressure | Net pull force |
|---|---|
| 0.5 MPa | 23.5 N |
| 0.7 MPa (max) | 36.7 N |
These are the usable pull forces after the return spring is subtracted, taken directly from the AirTAC single-acting thrust table. Minimum operating pressure is set by the spring, so this model needs at least the lower pressure shown to move.
Model Code: Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR
| PTB | JIS pen-size single acting, pull type (spring extend) mini-cylinder series. |
|---|---|
| 10 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| S | Built-in magnet for magnetic-switch position sensing (omit = no magnet). |
| R | Back cover: R axial inlet (bore-dependent). |
Mounting accessories: LB, FA, CJ. Related PB-family variants: PB (double acting), PSB (single-acting push), PBD (double rod), PBR (front-mount).
Where the Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR Is Used
Hold-Down Clamping
Maintains tension on light materials with the rod extended, using the 23.5 N pull to retract and release the clamp when air is applied.
Wire Belt Tensioner
Applies consistent pulling force on a filament or belt, utilizing the fail-safe spring-extend feature to preserve tension during pneumatic dropouts.
Retract-To-Open Gate
Pulls a lightweight diverter gate out of the product flow path on signal, allowing the internal spring to push the barrier back into blocking position by default.
Is the Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR the Right Cylinder?
Selecting this 10 mm bore model involves balancing the 23.5 N net pull at 0.5 MPa against your payload requirements. If your application demands less force, the Ø6 bore offers 7.1 N, whereas stepping up to the Ø12 bore yields 33.1 N. Note that the internal return spring establishes a minimum 0.2 MPa operating pressure before the rod will move. This 60 mm stroke represents the maximum single-acting limit for this series.
The included -S magnet enables position feedback, and the R suffix denotes an axial inline air inlet. Keep in mind the slender Ø4 mm rod is engineered for coaxial thrust; over this 60 mm extension, adding an external linear bearing is crucial to prevent side-loading damage. Furthermore, the fixed TPU bumper only absorbs energy in the final few millimeters—at higher cycling speeds with real tooling mass, meter-out exhaust flow control or an external shock absorber is recommended.
Quick checklist
- ✓ Net pull force at your working pressure
- ✓ Only one air line / solenoid needed
- ✓ Fail-safe extend on air loss
- ✓ Magnet (S) for sensors?
- ✓ Stroke ≤ 60 mm (single-acting limit)
- ✓ Keep the load coaxial — avoid side load
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.2 – 0.7 MPa operating pressure.
- check Allow for spring force in the stroke direction.
- check Do not add an external return mechanism.
- check Keep the load coaxial; avoid side load on the thin rod.
- check Do not dismantle the front or back cover.
Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR FAQ
This cylinder provides a net pull force of 23.5 N at 0.5 MPa and 36.7 N at the 0.7 MPa maximum. The internal spring requires a minimum of 0.2 MPa to initiate retraction. Upon air loss, the spring automatically extends the rod to its fail-safe outward position.
The -S suffix indicates a built-in piston magnet compatible with reed or electronic switches. The cylinder uses a fixed TPU bumper at each end to decelerate the last few millimeters of travel; it is not adjustable, so high-speed loads may require external shock absorption.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC PTB Pen-Size Cylinders
Request a Quote for Airtac PTB Single Acting Pen-Type Cylinder PTB10X60SR
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.