
The AirTAC SE50 Standard Cylinder SE50X100LB is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X100LB is a double-acting, single-rod ISO 15552 profile cylinder engineered for 982 N push force at 0.5 MPa. Fitted with an LB foot mounting bracket, this 50 mm bore unit operates at speeds between 30 and 800 mm/s via a PT1/4 port. Its extruded aluminum square barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames without protruding hardware.
This model features field-adjustable air cushioning at both ends, allowing technicians to tune end-of-stroke deceleration via a set screw to eliminate hard mechanical impacts during high-speed cycling. Because this specific SKU lacks the built-in -S magnet, it does not directly support AirTAC CMSE or DMSE electronic position sensors without modification.
| Model | Airtac SE50 Standard Cylinder SE50X100LB |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push at 0.5 MPa required to snap heavy corrugated carton flaps into position on continuous packaging lines.
Uses the 100 mm stroke and LB foot mount to raise and lower a solid stop blade on a 50 mm conveyor section reliably.
Delivers steady clamping force to seat bearings into housings without exceeding the 200 kgf maximum structural limit.
Stepping down to a 40 mm bore drops the 0.5 MPa push output to 628 N, while moving up to a 63 mm bore increases it to 1559 N, giving you clear sizing boundaries around this 982 N unit. As a standard ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other ISO 15552 cylinders, sharing standardized LB foot mounting and PT1/4 port interfaces. Note that the adjustable air cushion only decelerates the piston near stroke end; it cannot hold a load if air pressure is lost. For position holding, consider a BSE rod lock variant.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X100LB delivers 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. It features a 20 mm rod with an M16x1.5 thread.
Yes, the SE50X100LB is dimensionally interchangeable per ISO 15552 standards, meaning it matches the standardized mounting footprint and PT1/4 port locations of other ISO 15552 profile cylinders for easy retrofitting.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.