
The AirTAC SE50 Standard Cylinder SE50X100SH is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 100mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X100SH is a double-acting single-rod ISO 15552 profile cylinder engineered for demanding thermal environments. It delivers a robust 982 N push force at 0.5 MPa and utilizes a high-temperature FKM seal, extending the operating range up to 150 C for washdown or hot-end machinery.
Its square extruded aluminum barrel eliminates external tie rods, yielding a compact, corrosion-resistant body that mounts flush against frames. The integrated -S magnet enables direct position tracking with AirTAC CMSE reed or DMSE electronic sensors along the three integrated sensor grooves.
| Model | Airtac SE50 Standard Cylinder SE50X100SH |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 100 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×100 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Deploys a 100 mm stroke to eject hot plastic parts, leveraging the 150 C FKM seal to survive ambient radiated heat near the mold platen.
Cycles a sealing jaw with 982 N push at 0.5 MPa, maintaining structural integrity inside a warm shrink-tunnel transfer zone.
Actuates a routing gate to push pans into a cooling oven, using the -S magnet to confirm gate position with a DMSE electronic sensor.
Selecting this 50 mm bore makes sense when heat exposure would degrade standard TPU seals. If your application runs cooler and requires less force, stepping down to the 40 mm bore yields 628 N push at 0.5 MPa. Conversely, moving up to the 63 mm bore provides 1559 N push for heavier loads. Because this is a double-acting cylinder, it will drift if air pressure is lost; use a BSE rod lock for fail-safe holding. Dimensionally interchangeable per ISO 15552, it serves as a direct replacement sharing the PT1/4 port and standardized mounting accessories.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa it provides 982 N push and 825 N pull; at 0.7 MPa push is 1374 N. The maximum push capacity is 200 kgf at 1.0 MPa. Thanks to the H seal option, it operates from -20 to 150 C at 30-800 mm/s.
Yes, it features a field-adjustable air cushion at both ends. You can tune the needle screw to decelerate the piston before the end cap, softening hard stops at speed. Note this cushion only decelerates; it does not lock or hold the load.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.