
The AirTAC SE50 Standard Cylinder SE50X1050S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1050mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1050S is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-stroke actuation. It delivers a robust 982 N push force at 0.5 MPa and handles an extended 1050 mm stroke, making it a made-to-order solution for demanding linear motion tasks. The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames while exposing standardized mounting dimensions for direct interchangeability with other ISO 15552 cylinders.
This specific configuration includes a built-in magnet (-S) for CMSE reed and DMSE electronic position sensing, ensuring precise end-of-stroke verification. The field-adjustable air cushioning at both ends allows technicians to dial in the exact deceleration rate to soften hard end stops at speed, protecting the machine assembly from shock. Operating at 30-800 mm/s, it uses a PT1/4 port and a Ø20 mm hard-chrome rod with an M16x1.5 thread.
| Model | Airtac SE50 Standard Cylinder SE50X1050S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1050 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1050 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a 1050 mm routing gate on a packaging conveyor, using the 982 N push force to reliably swing heavy pallet diverters into position.
Pushes metal sheet blanks into a press brake at extended length, utilizing the long stroke and adjustable cushioning to decelerate the carriage smoothly.
Drives a multi-tier automated storage lift, where the DMSE electronic sensors track the 50 mm piston across the full 1050 mm travel distance.
Choosing this 50 mm bore depends on your force and stroke requirements. At 0.5 MPa, it provides 982 N of push force; if your load is lighter, stepping down to the 40 mm bore yields 628 N, while stepping up to the 63 mm bore offers 1559 N for heavier payloads. Because this is a 1050 mm stroke—well beyond the 1200 mm maximum standard stroke for this bore—it is classified as non-standard and made-to-order. Furthermore, at this extended length, the unsupported piston rod is highly susceptible to bending under side loads; integrating an external guide rail is strongly recommended to prevent premature rod-bearing wear.
For position feedback, the built-in magnet pairs seamlessly with AirTAC CMSE and DMSE sensors along the three-sided sensor groove. Remember that a standard SE cylinder cannot hold a load if air pressure is lost or the valve is centered—the piston will drift. If your application requires true static holding on a vertical load without live pressure, consider the BSE rod-lock variant instead.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
This 50 mm bore cylinder provides 982 N push and 825 N pull at 0.5 MPa, and 1374 N push at 0.7 MPa, with a maximum push capacity of 200 kgf at 1.0 MPa. The 1050 mm stroke is a non-standard, made-to-order length that exceeds the 1200 mm standard maximum for this bore.
Yes, it is dimensionally interchangeable per ISO 15552, meaning it shares the exact mounting footprint and hardware of other profile cylinders. However, it is double-acting and does not hold a load if air is lost; the adjustable air cushion only decelerates the piston near the stroke end and acts as no lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.