
The AirTAC SE50 Standard Cylinder SE50X106S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 106mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X106S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver a 982 N push force at 0.5 MPa. Its square extruded aluminum barrel eliminates external tie rods, yielding a compact body that resists corrosion and mounts flush against machine frames.
Because this unit includes the -S magnet code, it is fully primed for position detection using AirTAC CMSE reed and DMSE electronic sensors. The integrated adjustable air cushioning at both ends allows technicians to field-tune end-of-stroke deceleration, softening hard impacts during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X106S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 106 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×106 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the precise 982 N push required to mechanically fold carton flaps on continuous packaging lines, utilizing the -S magnet to confirm flap closure position.
Actuates routing gates on parcel sorting conveyors, relying on the adjustable end cushions to soften directional changes during high-speed 30-800 mm/s cycling.
Drives small parts ejector pins on injection molding platens, where the corrosion-resistant extruded profile barrel withstands humid shop environments.
If your application requires less force, stepping down to the 40 mm bore yields a 628 N push at 0.5 MPa, whereas moving up to the 63 mm bore provides 1559 N of thrust. As a standard ISO 15552 profile cylinder, this 50 mm bore, 106 mm stroke, PT1/4 ported unit serves as a direct dimensional replacement for other ISO 15552 cylinders, sharing standard mounting accessories like FA front flanges or LB foot brackets. Note that while the -S magnet enables precise end-position sensing, a standard SE cylinder will drift if air pressure is lost; use a BSE variant if your cycle demands positive load holding.
With a 106 mm stroke, side loading is minimal, but always ensure the rod-end thread M16x1.5 is aligned to prevent premature seal wear.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X106S delivers 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X106S is dimensionally interchangeable per ISO 15552 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, matching the 50 mm bore, 106 mm stroke, PT1/4 port, and standard mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.