
The AirTAC SE50 Standard Cylinder SE50X1250S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1250mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1250S is a double-acting, single-rod ISO 15552 profile cylinder engineered for demanding pneumatic tasks. Operating at 0.5 MPa, it generates 982 N of push force and 825 N of pull force, scaling to 1374 N push at 0.7 MPa. Because this unit features a built-in magnet (-S), it directly supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection.
The extruded aluminum barrel design omits external tie rods, yielding a compact, flush-mounting body that naturally resists corrosion and simplifies sensor placement across its three integrated grooves. Field-adjustable pneumatic cushioning at both ends allows you to tune end-stop deceleration for heavy loads moving at speed. Since the 1250 mm stroke exceeds the 1200 mm standard maximum, this specific unit is manufactured as a made-to-order configuration.
| Model | Airtac SE50 Standard Cylinder SE50X1250S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1250 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Actuates a routing gate over a 1250 mm span to separate glass containers, utilizing the 982 N push force to overcome friction on guide rails.
Drives a long-reach mechanical arm to fold large carton flaps, relying on the DMSE electronic sensors to confirm full extension.
Applies precise 825 N pull tension across wide fabric webs during dyeing, keeping the material flat without external tie-rod interference.
When sizing this bore, stepping down to a 40 mm cylinder reduces the 0.5 MPa push to 628 N, while stepping up to a 63 mm bore increases it to 1559 N. At 1250 mm, the unsupported stroke length places significant bending loads on the Ø20 mm rod and its bearing; an external guide is highly recommended to prevent premature wear. As a standard ISO 15552 profile cylinder, it offers dimensional interchangeability for retrofitting existing setups. Note that the adjustable cushion only decelerates the piston near stroke end; it does not hold a load if air pressure is lost.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The SE50X1250S delivers 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. It features a 50 mm bore, a PT1/4 port, a Ø20 mm rod with an M16x1.5 thread, and operates at speeds of 30-800 mm/s.
Yes, the SE50X1250S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can drop it into existing mounting hardware, but note that the 1250 mm stroke is a non-standard made-to-order length exceeding the 1200 mm maximum.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.