
The AirTAC SE50 Standard Cylinder SE50X138S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 138mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X138S is a double-acting single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force and 825 N of pull force at 0.5 MPa. Because this 138 mm stroke falls outside the standard incremental list, it is produced as a made-to-order unit to fit precise machinery spacing requirements without requiring external spacers.
The extruded aluminum barrel omits external tie rods entirely, yielding a compact footprint that mounts flush against machine frames while resisting corrosion. Equipped with a built-in magnet, this unit supports AirTAC CMSE reed and DMSE electronic sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows technicians to tune the end-of-stroke deceleration via a set screw, softening hard impacts during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X138S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 138 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×138 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the mechanical arms that fold corrugated carton flaps prior to hot-melt sealing, utilizing the 138 mm stroke to clear varying box heights while applying 982 N of push force.
Actuates a routing gate on a packaging conveyor, extending rapidly to redirect heavy pallets onto a secondary spur without requiring bulky external spacers for the non-standard stroke.
Secures aluminum castings inside a CNC machining center, using the built-in DMSE electronic sensor to confirm clamp engagement before the spindle initiates its cutting cycle.
When sizing this actuator, you can step down to the 40 mm bore for lighter loads, which yields 628 N push at 0.5 MPa, or step up to the 63 mm bore for heavier demands, providing 1559 N push at 0.5 MPa. The 50 mm bore here provides a balanced middle ground for mid-tier actuation. To replace an existing unit, match the 50 mm bore, 138 mm stroke, PT1/4 port, and the required mounting accessory, ensuring the -S magnet is present for sensor feedback.
Keep in mind that the adjustable air cushion only decelerates the piston near the stroke ends; it does not lock or hold the load. If your process loses air pressure or centers the valve, the rod will drift. For strict load-holding safety, consider the BSE rod-lock variant or an external pilot-operated check valve. Because this is a non-standard 138 mm stroke, confirm the exact extended and retracted dimensions from the datasheet before finalizing your CAD model.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X138S is dimensionally interchangeable per ISO 15552 standards. Its mounting interface, PT1/4 ports, and 50 mm bore dimensions match competing profile cylinders, allowing for a seamless retrofit without altering your existing machine hole patterns.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.