
The AirTAC SE50 Standard Cylinder SE50X1400 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1400 is a double-acting single-rod ISO 15552 profile cylinder engineered for long-reach linear motion. It delivers a theoretical push force of 982 N at 0.5 MPa and a maximum push capacity of 200 kgf at 1.0 MPa. Because this 1400 mm stroke exceeds the standard 1200 mm maximum for a 50 mm bore, it is produced as a non-standard made-to-order unit.
The extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies sensor placement along three integrated grooves. Although this specific SKU lacks the -S magnet for CMSE or DMSE position sensing, the end caps house field-adjustable pneumatic cushioning at both ends to decelerate the piston smoothly over the extended travel.
| Model | Airtac SE50 Standard Cylinder SE50X1400 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1400 mm extended stroke to push cartons across a wide sorting conveyor belt, utilizing the 982 N push force to overcome friction without stalling.
Sweeps layered product onto a pallet in automated warehouses, where the long travel accommodates varying pallet widths and the 200 kgf max thrust handles dense loads.
Deploys a long guide arm to align large fabric rolls at winding machines, benefiting from the tie-rod-free profile body that prevents lint snagging in dusty environments.
When sizing this actuator, compare its 982 N push at 0.5 MPa against its neighbors: step down to a 40 mm bore for 628 N if the load is lighter, or step up to a 63 mm bore for 1559 N if you need higher thrust margins. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 cylinders, matching the 50 mm bore, 1400 mm stroke, PT1/4 port, and standard mounting accessories without footprint changes.
Because the 1400 mm stroke creates a long unsupported rod, the M16x1.5 piston rod and internal bearing face significant bending moments under side loads; an external guide rail is strongly recommended to prevent premature seal wear. Note that the adjustable air cushion only decelerates the piston near stroke end and does not hold the load—if air pressure is lost, the cylinder will drift, requiring a BSE rod lock or external pilot check valve for position holding.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N. The maximum push capacity is 200 kgf at 1.0 MPa. It operates within a pressure range of 0.15-1.0 MPa and a speed range of 30-800 mm/s.
Yes, the SE50X1400 is dimensionally interchangeable per ISO 15552 standards. You can drop it in as a replacement for other ISO 15552 profile cylinders using the same PT1/4 ports and 50 mm mounting hardware. Note that this 1400 mm stroke is a non-standard made-to-order length.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.