
The AirTAC SE50 Standard Cylinder SE50X1400S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1400mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1400S is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-reach linear motion. It delivers 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa, utilizing a 20 mm hard-chrome rod with an M16x1.5 thread. Because the 1400 mm stroke exceeds the 1200 mm standard maximum, this unit is produced as a made-to-order configuration.
The extruded aluminum barrel omits external tie rods, yielding a compact, corrosion-resistant body that mounts flush in tight spaces. Field-adjustable pneumatic cushioning at both ends allows you to dial out harsh end-stop impacts during high-speed traversal. Equipped with a built-in magnet (-S), it interfaces seamlessly with AirTAC CMSE reed and DMSE electronic sensors for mid-stroke position detection.
| Model | Airtac SE50 Standard Cylinder SE50X1400S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1400 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1400 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 1400 mm stroke to index packaging materials across a wide carton erector frame, relying on the 982 N push force to overcome guide friction.
Ejects long sheet metal panels from a press brake bed, where the adjustable end cushions absorb the impact of heavy tooling returns at speed.
Pushes completed product layers onto a palletizer sweep arm, using the built-in magnet and DMSE sensors to confirm full extension at 1400 mm.
At 0.5 MPa, this 50 mm bore generates 982 N of thrust. If your drive force is insufficient, stepping up to the 63 mm bore yields 1559 N. Conversely, scaling down to the 40 mm bore provides 628 N for lighter payloads. Keep in mind that a standard SE does not hold a load when air is exhausted or a valve centers; the piston will drift, so a BSE rod lock or external pilot-operated check valve is required for fail-safe position holding.
For a 1400 mm stroke, the unsupported rod length introduces significant side-load and rod-bearing bending risks. Even with the robust 20 mm rod, you must use an external guide rail to prevent premature seal wear and piston scoring. As a dimensionally interchangeable ISO 15552 cylinder, it serves as a direct replacement for other ISO 15552 profile cylinders, utilizing the same PT1/4 port and standard mounting accessories.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
The 50 mm bore provides a push force of 982 N and a pull force of 825 N at 0.5 MPa. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable with ISO 15552 profile cylinders and uses the same mounting interface. However, the adjustable air cushion only decelerates the piston near stroke end; it does not lock the rod. For position holding without live air pressure, use an AirTAC BSE rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.