
The AirTAC SE50 Standard Cylinder SE50X1450S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1450mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1450S is a double-acting, single-rod ISO 15552 profile cylinder engineered for long-stroke pneumatic automation. It delivers a robust 982 N of push force at 0.5 MPa and features a PT1/4 port paired with a 20 mm hard-chrome plated rod. Because this unit carries the -S option, it includes a built-in magnet for seamless positioning feedback using AirTAC CMSE reed or DMSE electronic sensors.
This actuator utilizes a square extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush into tight machine envelopes. The 1450 mm stroke exceeds the 1200 mm standard maximum, making this a made-to-order configuration tailored for extended travel. Field-adjustable air cushions at both ends allow technicians to tune end-of-stroke deceleration, softening hard mechanical impacts during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X1450S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1450 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Utilizes the 1450 mm travel to push heavy pallets between processing stations, relying on the 982 N push force to overcome friction without stalling.
Extracts totes from deep-shelf racking in high-bay warehouses, where the -S magnet triggers DMSE electronic sensors to confirm tote handoff.
Strokes across wide palletizing cells to feed empty pallets into wrapping lines, tuning the adjustable end cushions to halt heavy pallets smoothly.
When sizing this actuator, note that the 982 N push at 0.5 MPa can be stepped down to the 628 N push of a bore 40 cylinder for lighter duties, or scaled up to the 1559 N thrust of a bore 63 unit if your payload demands more force. As a standard ISO 15552 profile cylinder, it serves as a direct dimensional replacement for other ISO 15552 cylinders, sharing standardized mounting hardware like FA front flanges or LB foot brackets. To complete your build, specify the PT1/4 port thread and ensure you order CMSE or DMSE sensors to leverage the built-in -S magnet.
Because the 1450 mm stroke is non-standard and far exceeds typical lengths, the unsupported 20 mm rod is highly susceptible to bending under lateral stress. You must incorporate an external linear guide to support the load and prevent rod-bearing damage, as the pneumatic cushion only decelerates the piston near the stroke ends and cannot hold the load if air pressure is lost.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
This 50 mm bore cylinder provides 982 N push and 825 N pull at 0.5 MPa, 1374 N push at 0.7 MPa, and a maximum push of 200 kgf at 1.0 MPa. The 1450 mm stroke exceeds the 1200 mm standard maximum, making it a non-standard, made-to-order travel length.
No, the adjustable air cushions only decelerate the piston near the end caps and do not function as a locking mechanism. If the pneumatic supply is lost or a valve is centered, the rod will drift, requiring an external rod lock or a BSE series cylinder for positive holding.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.