
The AirTAC SE50 Standard Cylinder SE50X145S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 145mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X145S is a double-acting single-rod ISO 15552 profile cylinder, delivering 982 N of push force and 825 N of pull force at 0.5 MPa. It features a square extruded aluminum barrel without external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames. Because it adheres to the ISO 15552 / VDMA 24562 dimensional standard, it serves as a direct replacement for other ISO 15552 cylinders, streamlining retrofit procurement.
This 50 mm bore unit includes a built-in magnet (S option) for non-contact position detection using AirTAC CMSE reed or DMSE electronic sensors. The field-adjustable pneumatic air cushion at both ends can be tuned via a set screw to soften hard end-of-stroke impacts at operating speeds up to 800 mm/s. This cushion only decelerates the piston near stroke end; it is not a locking mechanism.
| Model | Airtac SE50 Standard Cylinder SE50X145S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 145 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×145 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 982 N push force at 0.5 MPa to reliably open and fold heavy corrugated cardboard flaps on high-speed packaging lines, relying on the adjustable cushion to soften the 145 mm stroke end stop.
Pivots routing gates on parcel sorters where the 825 N pull force retracts the arm quickly, while the built-in -S magnet triggers DMSE electronic sensors to confirm package passage.
Positions sheet metal back-gauge stops on a press brake, using the 145 mm stroke to set bend depths, benefiting from the no-tie-rod profile that mounts flush to prevent debris buildup.
At 0.5 MPa, this 50 mm bore provides 982 N push and 825 N pull. If your application requires less force, stepping down to the 40 mm bore yields 628 N push, whereas stepping up to the 63 mm bore provides 1559 N push. To match an existing fixture, verify you need a 145 mm stroke, a PT1/4 port, and M16x1.5 rod-end threading. The standard ISO 15552 mounting interface shares hardware across Basic, FA, and TC configurations.
Because the stroke is 145 mm, the 20 mm rod and its bearing face moderate side-loading stress, but for long unsupported loads an external guide is recommended to prevent rod bending. Note that a plain SE cylinder will drift if air pressure is lost; if your machine must hold a load safely during exhaust or valve centering, pair it with a BSE rod lock or an external pilot-operated check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the 50 mm bore provides 982 N push and 825 N pull force. At 0.7 MPa, the push force is 1374 N, and the maximum push force is 200 kgf at 1.0 MPa. The operating speed range is 30-800 mm/s.
Yes. The SE50X145S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can use it as a direct replacement for other ISO 15552 profile cylinders, retaining your existing mounting hardware and PT1/4 pneumatic ports. The built-in -S magnet also works seamlessly with AirTAC CMSE and DMSE sensors.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.