
The AirTAC SE50 Standard Cylinder SE50X1500 is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 1500mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X1500 is a double-acting single-rod ISO 15552 profile cylinder, engineered to deliver a 982 N push force at 0.5 MPa across a 1500 mm stroke. Because this stroke exceeds the 1200 mm standard limit, it is manufactured as a made-to-order unit. The extruded aluminum barrel omits external tie rods, yielding a compact, flush-mounting body that resists corrosion and simplifies bracket installation.
This unit features a Ø20 mm piston rod with an M16x1.5 thread and a PT1/4 port. Field-adjustable pneumatic cushioning at both ends allows technicians to fine-tune end-of-stroke deceleration, softening hard impacts when cycling at speeds up to 800 mm/s. This SKU is built without a position-sensor magnet, meaning external proximity switches cannot be fitted without modification.
| Model | Airtac SE50 Standard Cylinder SE50X1500 |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 1500 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×1500 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Pushes products between parallel conveyor lanes across a 1500 mm span, utilizing the 982 N thrust to reliably divert heavy cartons at high throughput speeds.
Actuates the lateral shifting of heavy textile beams into weaving machinery, where the 1500 mm extension accommodates wide-format material loading without manual intervention.
Deploys a 1500 mm stroke to separate and feed large sheet metal or composite panels from a vertical storage magazine into a downstream machining center.
At 0.5 MPa, this 50 mm bore generates 982 N of thrust. If your assembly requires less force, stepping down to the 40 mm bore drops the output to 628 N, whereas upgrading to the 63 mm bore increases thrust to 1559 N for heavier payloads. Because the 1500 mm stroke is non-standard, expect a made-to-order lead time rather than off-the-shelf shipping.
With a 1500 mm unsupported length, the Ø20 mm rod is highly susceptible to side-load bending and bearing wear; an external guide rail is strongly recommended to prevent premature seal failure. As a standard ISO 15552 cylinder, it serves as a direct dimensional replacement for other brands' profile cylinders, utilizing shared mounting hardware and a PT1/4 port. Note that the air cushion only decelerates the piston near stroke end—it does not hold a load. If the application must maintain position upon air loss, an external pilot-operated check valve or a BSE rod-lock variant is required.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
This 50 mm bore cylinder provides 982 N of push force and 825 N of pull force at 0.5 MPa. At 0.7 MPa, the push force increases to 1374 N, with a maximum rated push of 200 kgf at 1.0 MPa. It operates at speeds between 30 and 800 mm/s.
Yes, its ISO 15552 mounting dimensions make it a direct replacement for other standard profile cylinders. However, the adjustable air cushion only decelerates the piston near the stroke ends and does not act as a brake; it cannot hold a vertical load when air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.