
The AirTAC SE50 Standard Cylinder SE50X150H is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 150mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X150H is a double-acting, single-rod ISO 15552 profile cylinder engineered for high-temperature tasks. It delivers 982 N of push force and 825 N of pull force at 0.5 MPa, utilizing a 50 mm bore and 150 mm stroke. The FKM (Viton) seal expands the operating temperature range up to 150 C, making it highly suitable for thermally demanding environments.
Built with an extruded aluminum barrel that eliminates external tie rods, the body is compact and corrosion-resistant. The field-adjustable pneumatic cushioning at both ends allows you to fine-tune end-of-stroke deceleration via a set screw, minimizing mechanical impact during high-speed cycling. Note that this specific SKU lacks a built-in magnet, so it is not wired for AirTAC CMSE or DMSE position sensors without modification.
| Model | Airtac SE50 Standard Cylinder SE50X150H |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Ideal for ejecting hot cured rubber parts from molding presses, utilizing the 150 C FKM seal to withstand ambient radiant heat while delivering 982 N push at 0.5 MPa.
Suited for diverting warm stamped metal components on conveyor lines, where the 150 mm stroke provides precise lateral displacement and the no-tie-rod profile resists debris buildup.
Reliable for automated opening and closing of industrial drying oven doors, leveraging the Viton seal to maintain integrity in continuous high-temperature laboratory environments.
Stepping up to the 63 mm bore yields 1559 N push at 0.5 MPa, whereas dropping to the 40 mm bore provides 628 N. This 50 mm model hits a solid middle ground for 200 kgf maximum thrust at 1.0 MPa. Remember that the adjustable air cushion only decelerates the piston near stroke end; it does not lock the rod. If your process requires absolute position holding upon air loss, you must integrate an external pilot-operated check valve or transition to a BSE rod-lock variant. Because the stroke is 150 mm, side-loading is minimal, but always verify the rod-end thread (M16x1.5) alignment to prevent premature bearing wear.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N push and 825 N pull force. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa. It operates on filtered air at 0.15-1.0 MPa, runs at 30-800 mm/s, and uses a PT1/4 port.
Yes, it is dimensionally interchangeable with any standard ISO 15552 profile cylinder, allowing you to drop it into existing mounting hardware like FA front flanges without modifications. However, it is a standard double-acting cylinder; the adjustable cushion only decelerates the piston near stroke end and does not hold a load if air pressure is lost.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.