
The AirTAC SE50 Standard Cylinder SE50X150S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 150mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X150S is a double-acting single-rod ISO 15552 profile cylinder offering a 982 N push force at 0.5 MPa. It features a square extruded aluminum barrel without external tie rods, yielding a compact footprint that resists corrosion and mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit supports CMSE reed and DMSE electronic position sensors for precise end-of-stroke verification. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-of-stroke deceleration via a simple screw, protecting payloads during 150 mm travel.
| Model | Airtac SE50 Standard Cylinder SE50X150S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 150 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×150 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 982 N of push force at 0.5 MPa to secure aluminum castings onto CNC machining centers, utilizing the adjustable cushion to soften hard end stops during rapid 150 mm clamping.
Drives folding arms on continuous flow packaging lines, where the built-in magnet triggers DMSE sensors to verify flap closure timing at speeds up to 800 mm/s.
Actuates sorting gates on logistics conveyor systems, relying on the tie-rod-free extruded profile for tight clearance mounting and smooth 825 N retraction force.
Select this 50 mm bore when an application demands 982 N of push force at 0.5 MPa. If your payload is lighter, stepping down to the 40 mm bore yields 628 N, while heavier dynamics require stepping up to the 63 mm bore for 1559 N. Remember that a standard SE cylinder relies on live air pressure to move; if air is lost, the piston drifts and cannot hold a load.
For retrofitting, this 150 mm stroke, PT1/4 ported cylinder is dimensionally interchangeable with other ISO 15552 cylinders, sharing standard mounting accessories. The 20 mm rod and M16x1.5 thread handle moderate side loads, though any stroke at or exceeding 300 mm warrants an external guide to prevent rod-bearing bending.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X150S is dimensionally interchangeable per ISO 15552 standards. It shares the exact mounting interface and PT1/4 port locations of other ISO 15552 profile cylinders, allowing a direct replacement without altering existing mounting hardware.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.