
The AirTAC SE50 Standard Cylinder SE50X160S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 160mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X160S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa and 1374 N at 0.7 MPa. It features a 50 mm bore, 160 mm stroke, and a PT1/4 port. The extruded aluminum barrel design omits external tie rods, yielding a compact, flush-mounting body that naturally resists corrosion and simplifies sensor placement along its three integrated grooves.
Equipped with a built-in magnet (-S), this unit directly supports AirTAC CMSE reed and DMSE electronic position switches for precise end-of-stroke verification. The field-adjustable pneumatic cushioning at both ends allows technicians to tune end-stop deceleration via a set screw, softening impacts during high-speed 30-800 mm/s cycling.
| Model | Airtac SE50 Standard Cylinder SE50X160S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 160 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Drives the folding mechanism on automated packaging lines, using the 982 N push force to snap heavy cardboard flaps into position before sealing at 160 mm stroke.
Actuates a routing flap on a conveyor system, relying on the adjustable end cushions to softly stop the 160 mm stroke at high cycling speeds without bouncing the load.
Pushes sample racks into a testing chamber, using the built-in magnet to trigger CMSE reed sensors that confirm the 50 mm bore is fully extended before the cycle begins.
When sizing this 50 mm bore actuator, evaluate your exact force requirements against its 982 N push at 0.5 MPa. If your load demands less energy, stepping down to the 40 mm bore yields 628 N of push force, whereas scaling up to the 63 mm bore provides a substantial 1559 N. Because this is a double-acting cylinder, note that it relies on continuous air pressure to move and hold the piston; if power drops, the load drifts, meaning a BSE rod lock is required for fail-safe positioning.
For a direct retrofit, this model is dimensionally interchangeable per ISO 15552 standards, matching other 50 mm bore, 160 mm stroke actuators with PT1/4 ports and standard mounting accessories. At 160 mm of travel, the 20 mm rod and M16x1.5 thread handle moderate side loading, but any long unsupported payload should utilize an external guide to prevent rod-bearing bending.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the SE50X160S generates 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The maximum push force is 200 kgf at 1.0 MPa.
No, the SE50X160S is a standard double-acting cylinder and the piston will drift if air is lost or the valve is centered. The adjustable air cushion only decelerates the piston near the stroke end; it is not a locking mechanism. For true position holding, consider the BSE series rod lock.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.