
The AirTAC SE50 Standard Cylinder SE50X165S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 165mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X165S is a double-acting single-rod profile cylinder built to the ISO 15552 standard. It delivers 982 N of push force and 825 N of pull force at 0.5 MPa, making it a robust mid-range actuator. The square extruded aluminum barrel eliminates external tie rods, resulting in a compact, corrosion-resistant body that mounts flush on machinery.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensors along the three integrated sensor grooves. The field-adjustable pneumatic cushioning at both stroke ends allows you to fine-tune end-of-travel deceleration, minimizing impact wear on moving assemblies.
| Model | Airtac SE50 Standard Cylinder SE50X165S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 165 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×165 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides the 982 N push stroke required to fold heavy cardboard flaps on continuous-motion carton packaging lines, using its 165 mm travel to clear the product path.
Actuates routing gates on conveyor systems, where the adjustable end cushion softens the 165 mm stroke stops to prevent jarring pallet impacts at high speed.
Indexes sample racks into a centrifuge chamber, utilizing the -S magnet and DMSE electronic sensors to confirm precise 165 mm extension positioning.
If your assembly requires less force, stepping down to a 40 mm bore yields 628 N of push at 0.5 MPa, whereas moving up to a 63 mm bore provides 1559 N. This SE50X165S is dimensionally interchangeable with any ISO 15552 cylinder, meaning you can drop it into existing footprints and reuse standard FA or LB mounting hardware without redesigning plates.
Because this is a double-acting cylinder, it will drift and cannot hold a load if air pressure is lost or the valve is centered; for position-holding safety, consider the AirTAC BSE rod-lock variant. At 165 mm stroke, side loads are moderate, but always verify rod-bearing bending loads and use an external guide if the load is heavy or asymmetric.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, the push force is 982 N and the pull force is 825 N. At 0.7 MPa, the push force is 1374 N. The maximum push force is 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X165S is dimensionally interchangeable per ISO 15552 standards. It shares the exact mounting interface and PT1/4 port locations of other ISO 15552 profile cylinders, allowing a direct retrofit without altering your machine's mounting holes.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.