
The AirTAC SE50 Standard Cylinder SE50X190S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 190mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X190S is a double-acting, single-rod ISO 15552 profile cylinder engineered to deliver 982 N of push force at 0.5 MPa. Its 50 mm bore and 190 mm stroke make it a robust mid-range actuator, while the square extruded aluminum barrel omits external tie rods for a flush, corrosion-resistant exterior that simplifies bracket mounting.
Because this unit includes the -S magnet code, it is fully primed for AirTAC CMSE reed or DMSE electronic position sensing along the three integrated sensor grooves. The field-adjustable pneumatic cushioning at both ends allows technicians to dial in end-of-stroke deceleration, softening hard impacts during high-speed cycling.
| Model | Airtac SE50 Standard Cylinder SE50X190S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 190 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×190 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Uses the 190 mm stroke and 982 N push to route plastic PET bottles between filling lanes without crushing the containers.
Deploys the -S magnet with a DMSE sensor to verify flap position precisely before taping corrugated cardboard cartons.
Cycles the safety enclosure at 30-800 mm/s, relying on the adjustable end cushions to prevent slamming the heavy steel panel.
When sizing this 50 mm bore actuator, compare its 982 N push at 0.5 MPa against the neighbouring 40 mm bore, which yields 628 N, or step up to the 63 mm bore for 1559 N if your payload demands more authority. As a 190 mm stroke is a non-standard made-to-order length, expect a brief production lead time. For direct retrofits, verify the PT1/4 port, M16x1.5 rod thread, and your required ISO 15552 mounting accessory kit.
Because the stroke exceeds 150 mm, ensure the piston rod bearing is not subjected to excessive bending moments; long unsupported strokes require an external guide to prevent premature seal wear. Note that a standard SE does not hold its position if air pressure is lost—the piston will drift—so applications requiring fail-safe load holding must pair it with a BSE rod lock or external pilot check valve.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force increases to 1374 N. The absolute maximum push force is 200 kgf when operated at the 1.0 MPa pressure limit.
Yes. The SE50X190S is dimensionally interchangeable per ISO 15552 / VDMA 24562 standards. You can swap it into existing foot or flange mounting holes, provided you match the PT1/4 port and M16x1.5 rod thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.