
The AirTAC SE50 Standard Cylinder SE50X200S is a genuine double-acting ISO 15552 / VDMA 24562 profile-barrel air cylinder with a Ø50mm bore and 200mm stroke, PT1/4 air ports and adjustable end cushioning. Its standardized mounting interface makes it interchangeable with other ISO 15552 cylinders at the mounting interface.
The AirTAC SE50X200S is a double-acting, single-rod ISO 15552 profile cylinder with a 50 mm bore and 200 mm stroke. It delivers a robust 982 N push force at 0.5 MPa, making it well-suited for mid-range industrial actuation. The extruded aluminum barrel lacks external tie rods, yielding a compact, corrosion-resistant body that mounts flush against machine frames.
Equipped with a built-in magnet (-S), this unit supports AirTAC CMSE reed and DMSE electronic position sensors for precise end-of-stroke detection. Field-adjustable pneumatic cushioning at both ends allows technicians to tune end-cap deceleration via a screw, softening hard mechanical stops during high-speed operations.
| Model | Airtac SE50 Standard Cylinder SE50X200S |
|---|---|
| Series | SE ISO 15552 profile cylinder |
| Bore size | Ø50 mm |
| Stroke | 200 mm |
| Acting type | Double acting |
| Port size | PT1/4 |
| Rod thread | M16×1.5 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C (0–150 °C with FKM seals) |
| Speed range | 30 – 800 mm/s |
| Cushion | Adjustable, 30 mm |
| Max stroke | Up to 1200 mm |
Specifications follow the official AirTAC SE series datasheet and ISO 15552 / VDMA 24562 dimensions. Confirm against the product label before installation. Port options: PT (standard) / G (BSPP).
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 982 N | 825 N |
| 0.7 MPa | 1374 N | — |
| Max (@1.0 MPa) | 200 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
| SE | ISO 15552 / VDMA 24562 profile-barrel double-acting cylinder. |
|---|---|
| 50 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSE / DMSE sensor sensing. |
Rod material: carbon steel (blank) / SUS420J2 (A) / SUS304 (B). Seals: TPU (blank) / FKM high-temp (H) / NBR (N). Thread: PT (blank) / G. Mounting: Basic, LB, FA, FB, CA, CB, CR, TC, FTC, TCM1, TCM2. Related SE-family variants: SED (double rod), SEJ (adjustable stroke), BSE (rod lock), BSED (double-rod rod lock).
Provides 982 N of clamping force at 0.5 MPa to secure aluminum castings inside CNC machining centers, utilizing the 200 mm stroke to clear the work envelope during part changes.
Drives mechanical folding arms on corrugated box sealing lines, using the adjustable end cushions to soften the impact of rapid flapping motions at high cycle rates.
Actuates routing gates on 50 mm pitch roller conveyors, relying on the CMSE reed switch signal to confirm gate position before upstream pallets advance.
When sizing this 50 mm bore actuator, evaluate your exact thrust needs: the smaller 40 mm bore provides 628 N of push at 0.5 MPa, while the larger 63 mm bore yields 1559 N. If your mechanism must hold a load vertically without continuous air pressure, note that a standard SE cylinder will drift when air is removed or a valve is centered; for those duties, select the BSE series rod lock or an external pilot-operated check valve. To replace an existing ISO 15552 cylinder, match the 50 mm bore, 200 mm stroke, PT1/4 port, and mounting accessory. Because the 200 mm stroke exceeds the 300 mm threshold, long unsupported piston rods are prone to rod-bearing bending under side loads; always incorporate an external guide to prevent premature seal wear.
AirtacDistr lists every SE50 order code with its price on one page at https://airtacdistr.com/products/airtac-se50-iso-air-cylinder
Quick checklist
At 0.5 MPa, this 50 mm bore cylinder provides 982 N of push force and 825 N of pull force. At 0.7 MPa, the push force is 1374 N, with a maximum push capacity of 200 kgf at 1.0 MPa. The operational speed range is 30-800 mm/s.
Yes, the SE50X200S is dimensionally interchangeable per ISO 15552 standards. You can drop it into existing foot or flange mounting patterns without modifying the machine, provided you match the PT1/4 port and M16x1.5 rod thread.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.